4501 datasheet(28/116 Pages) RENESAS

28 / 116 page

Rev.3.01

2005.02.07

page 28 of 112

REJ03B0104-0301

4501 Group

(5) Timer interrupt request flags (T1F, T2F)

Each timer interrupt request flag is set to “1” when each timer

underflows. The state of these flags can be examined with the skip

instructions (SNZT1, SNZT2).

Use the interrupt control register V1 to select an interrupt or a skip

instruction.

An interrupt request flag is cleared to “0” when an interrupt occurs

or when the next instruction is skipped with a skip instruction.

(6) Count start synchronization circuit (timer 1)

Timer 1 has the count start synchronous circuit which synchronizes

the input of INT pin, and can start the timer count operation.

Timer 1 count start synchronous circuit function is selected by set-

ting the bit 0 of register W1 to “1.” The control by INT pin input can

be performed by setting the bit 0 of register I1 to “1.”

The count start synchronous circuit is set by level change (“H”

→“L”

or “L”

→“H”) of INT pin input. This valid waveform is selected by bits

1 (I11) and 2 (I12) of register I1 as follows;

• I11 = “0”: Synchronized with one-sided edge (falling or rising)

• I11 = “1”: Synchronized with both edges (both falling and rising)

When register I11=“0” (synchronized with the one-sided edge), the ris-

ing or falling waveform can be selected by the bit 2 of register I1;

• I12 = “0”: Falling waveform

• I12 = “1”: Rising waveform

When timer 1 count start synchronous circuit is used, the count

start synchronous circuit is set, the count source is input to each

timer by inputting valid waveform to INT pin. Once set, the count

start synchronous circuit is cleared by clearing the bit I10 to “0” or

reset.

However, when the count auto-stop circuit is selected (register W22

= “1”), the count start synchronous circuit is cleared (auto-stop) at

the timer 1 underflow.

(7) Count auto-stop circuit (timer 1)

Timer 1 has the count auto-stop circuit which is used to stop timer

1 automatically by the timer 1 underflow when the count start syn-

chronous circuit is used.

The count auto-stop cicuit is valid by setting the bit 2 of register W2

to “1”. It is cleared by the timer 1 underflow and the count source to

timer 1 is stopped.

This function is valid only when the timer 1 count start synchronous

circuit is selected.

(3) Timer 1 (interrupt function)

Timer 1 is an 8-bit binary down counter with the timer 1 reload reg-

ister (R1). Data can be set simultaneously in timer 1 and the reload

ecute the T1AB instruction to set data to timer 1. Data can be

written to reload register (R1) with the TR1AB instruction.

When writing data to reload register R1 with the TR1AB instruction,

the downcount after the underflow is started from the setting value

of reload register R1.

Timer 1 starts counting after the following process;

➀ set data in timer 1, and

➁ set the bit 1 of register W1 to “1.”

However, INT pin input can be used as the start trigger for timer 1

count operation by setting the bit 0 of register W1 to “1.”

Also, in this time, the auto-stop function by timer 1 underflow can

be performed by setting the bit 2 of register W2 to “1.”

When a value set is n, timer 1 divides the count source signal by n

+ 1 (n = 0 to 255).

Once count is started, when timer 1 underflows (the next count

pulse is input after the contents of timer 1 becomes “0”), the timer

1 interrupt request flag (T1F) is set to “1,” new data is loaded from

reload register R1, and count continues (auto-reload function).

Data can be read from timer 1 with the TAB1 instruction. When

reading the data, stop the counter and then execute the TAB1 in-

struction.

(4) Timer 2 (interrupt function)

Timer 2 is an 8-bit binary down counter with the timer 2 reload reg-

ister (R2). Data can be set simultaneously in timer 2 and the reload

ecute the T2AB instruction to set data to timer 2.

Timer 2 starts counting after the following process;

➀ set data in timer 2,

➁ select the count source with the bits 0 and 1 of register W2, and

➂ set the bit 3 of register W2 to “1.”

When a value set is n, timer 2 divides the count source signal by n

+ 1 (n = 0 to 255).

Once count is started, when timer 2 underflows (the next count

pulse is input after the contents of timer 2 becomes “0”), the timer

2 interrupt request flag (T2F) is set to “1,” new data is loaded from

reload register R2, and count continues (auto-reload function).

Data can be read from timer 2 with the TAB2 instruction. When

reading the data, stop the counter and then execute the TAB2 in-

struction.

4501 датащи(PDF) 28 Page - Renesas Technology Corp

4501 датащи(HTML) 28 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL