ST72334J2TASLASHXXX datasheet(51/150 Pages) STMICROELECTRONICS

51 / 150 page

ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto

51/150

WATCHDOG TIMER (Cont’d)

The application program must write in the CR reg-

ister at regular intervals during normal operation to

prevent an MCU reset. The value to be stored in

the CR register must be between FFh and C0h

(see Table 12 .Watchdog Timing (fCPU = 8 MHz)):

– The WDGA bit is set (watchdog enabled)

– The T6 bit is set to prevent generating an imme-

diate reset

– The T[5:0] bits contain the number of increments

which represents the time delay before the

watchdog produces a reset.

Table 12.Watchdog Timing (fCPU = 8 MHz)

Notes: Following a reset, the watchdog is disa-

bled. Once activated it cannot be disabled, except

by a reset.

The T6 bit can be used to generate a software re-

set (the WDGA bit is set and the T6 bit is cleared).

If the watchdog is activated, the HALT instruction

will generate a Reset.

13.1.4 Hardware Watchdog Option

If Hardware Watchdog is selected by option byte,

the watchdog is always active and the WDGA bit in

the CR is not used.

Refer to the device-specific Option Byte descrip-

tion.

13.1.5 Low Power Modes

13.1.6 Interrupts

None.

13.1.7 Register Description

CONTROL REGISTER (CR)

Read/Write

Reset Value: 0111 1111 (7Fh)

Bit 7 = WDGA Activation bit.

This bit is set by software and only cleared by

hardware after a reset. When WDGA = 1, the

watchdog can generate a reset.

0: Watchdog disabled

1: Watchdog enabled

Note: This bit is not used if the hardware watch-

dog option is enabled by option byte.

Bit 6:0 = T[6:0] 7-bit timer (MSB to LSB).

These bits contain the decremented value. A reset

is produced when it rolls over from 40h to 3Fh (T6

becomes cleared).

STATUS REGISTER (SR)

Read/Write

Reset Value*: 0000 0000 (00h)

Bit 0 = WDOGF Watchdog flag.

This bit is set by a watchdog reset and cleared by

software or a power on/off reset. This bit is useful

for distinguishing power/on off or external reset

and watchdog reset.

0: No Watchdog reset occurred

1: Watchdog reset occurred

* Only by software and power on/off reset

Note: This register is not used in versions without

LVD Reset.

CR Register

initial value

WDG timeout period

(ms)

Max

FFh

98.304

Min

C0h

1.536

Mode

Description

WAIT

No effect on Watchdog.

HALT

Immediate reset generation as soon as the

HALT instruction is executed if the Watch-

dog is activated (WDGA bit is set).

WDGA

WDOGF

ST72334J2TA/XXX датащи(PDF) 51 Page - STMicroelectronics

ST72334J2TA/XXX датащи(HTML) 51 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL