TMS320DM335 datasheet(29/156 Pages) TI

29 / 156 page

2.4.7

Universal Serial Bus (USB) Interface

2.4.8

Audio Interfaces

TMS320DM335

Digital Media System-on-Chip (DMSoC)

www.ti.com

SPRS528 – JULY 2008

The Universal Serial Bus (USB) interface supports the USB2.0 High-Speed protocol and includes dual-role

Host/Slave support. However, no charge pump is included.

Table 2-13. USB Terminal Functions

TERMINAL

TYPE(1)

OTHER(2)(3)

DESCRIPTION

NAME

NO.

USB D+ (differential signal pair).

USB_DP

A I/O/Z

VDDA33_USB

When USB is not used, this signal should be connected to VSS_USB.

USB D- (differential signal pair).

USB_DM

A I/O/Z

VDDA33_USB

When USB is not used, this signal should be connected to VSS_USB.

USB reference current output

Connect to VSS_USB_REF via 10K ohm , 1% resistor placed as close to the device

USB_R1

A I/O/Z

as possible.

When USB is not used, this signal should be connected to VSS_USB.

USB operating mode identification pin

For Device mode operation only, pull up this pin to VDD with a 1.5K ohm resistor.

For Host mode operation only, pull down this pin to ground (VSS) with a 1.5K ohm

USB_ID

A I/O/Z

VDDA33_USB

resistor.

If using an OTG or mini-USB connector, this pin will be set properly via the

cable/connector configuration.

When USB is not used, this signal should be connected to VSS_USB.

For host or device mode operation, tie the VBUS/USB power signal to the USB

connector.

USB_VBUS

A I/O/Z

VDD

When used in OTG mode operation, tie VBUS to the external charge pump and

to the VBUS signal on the USB connector.

When the USB is not used, tie VBUS to VSS_USB.

Digital output to control external 5 V supply

USB_DRVVBUS

O/Z

VDD

When USB is not used, this signal should be left as a No Connect.

USB Ground Reference

VSS_USB_REF

GND

VDD

Connect directly to ground and to USB_R1 via 10K ohm, 1% resistor placed as

close to the device as possible.

Analog 3.3 V power USBPHY

VDDA33_USB

PWR

VDD

When USB is not used, this signal should be connected to VSS_USB.

Common mode 3.3 V power for USB PHY (PLL)

VDDA33_USB_PLL

PWR

VDD

When USB is not used, this signal should be connected to VSS_USB.

Analog 1.3 V power for USB PHY

VDDA13_USB

PWR

VDD

When USB is not used, this signal should be connected to VSS_USB.

Digital 1.3 V power for USB PHY

VDDD13_USB

PWR

VDD

When USB is not used, this signal should be connected to VSS_USB.

(1)

I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal.

(2)

Specifies the operating I/O supply voltage for each signal. See Section 5.3 , Power Supplies for more detail.

(3)

PD = pull-down, PU = pull-up. (To pull up a signal to the opposite supply rail, a 1 k

Ω resistor should be used.)

The DM335 includes two Audio Serial Ports (ASP ports), which are backward compatible with other TI

ASP serial ports and provide I2S audio interface. One interface is multiplexed with GIO signals.

Table 2-14. ASP Terminal Functions

TERMINAL

TYPE(1)

OTHER(2)(3)

DESCRIPTION

NAME

NO.

ASP0_CL

ASP0: Receive Clock

KR/

F17

I/O/Z

VDD

GIO: GIO[026]

GIO026

(1)

I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal.

(2)

Specifies the operating I/O supply voltage for each signal. See Section 5.3, Power Supplies for more detail.

(3)

PD = pull-down, PU = pull-up. (To pull up a signal to the opposite supply rail, a 1 k

Ω resistor should be used.)

Submit Documentation Feedback

Device Overview

TMS320DM335 датащи(PDF) 29 Page - Texas Instruments

TMS320DM335 датащи(HTML) 29 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL