TMS320VC549 datasheet(11/64 Pages) TI

11 / 64 page

TMS320VC549

FIXEDPOINT DIGITAL SIGNAL PROCESSOR

SPRS078G − SEPTEMBER 1998 − REVISED OCTOBER 2004

POST OFFICE BOX 1443

• HOUSTON, TEXAS 77251−1443

Signal Descriptions (Continued)

TERMINAL

DESCRIPTION

NAME

DESCRIPTION

TYPE†

IEEE1149.1 TEST PINS

TCK

IEEE standard 1149.1 test clock. Pin with internal pullup device. This is normally a free-running clock signal with

a 50% duty cycle. The changes on the test-access port (TAP) of input signals TMS and TDI are clocked into the

TAP controller, instruction register, or selected test data register on the rising edge of TCK. Changes at the TAP

output signal (TDO) occur on the falling edge of TCK.

TDI

IEEE standard 1149.1 test data input. Pin with internal pullup device. TDI is clocked into the selected register

(instruction or data) on a rising edge of TCK.

TDO

O/Z

IEEE standard 1149.1 test data output. The contents of the selected register (instruction or data) is shifted out

of TDO on the falling edge of TCK. TDO is in the high-impedance state except when the scanning of data is in

progress. TDO also goes into the high-impedance state when EMU1/OFF is low.

TMS

IEEE standard 1149.1 test mode select. Pin with internal pullup device. This serial control input is clocked into

the TAP controller on the rising edge of TCK.

TRST

IEEE standard 1149.1 test reset. TRST, when high, gives the IEEE standard 1149.1 scan system control of the

operations of the device. If TRST is not connected or driven low, the device operates in its functional mode, and

the IEEE standard 1149.1 signals are ignored. Pin with internal pulldown device.

EMU0

I/O/Z

Emulator interrupt 0 pin. When TRST is driven low, EMU0 must be high for the activation of the EMU1/OFF

condition. When TRST is driven high, EMU0 is used as an interrupt to or from the emulator system and is defined

as input/output by way of IEEE standard 1149.1 scan system. This pin should be pulled high with a separate

4.7-k

Ω resistor.

EMU1/OFF

I/O/Z

Emulator interrupt 1 pin/disable all outputs. When TRST is driven high, EMU1/OFF is used as an interrupt to or

from the emulator system and is defined as input/output by way of IEEE standard 1149.1 scan system. When

TRST is driven low, EMU1/OFF is configured as OFF. The EMU1/OFF signal, when active low, puts all output

drivers into the high-impedance state. This pin should be pulled high with a separate 4.7-k

Ω resistor. Note that

OFF is used exclusively for testing and emulation purposes (not for multiprocessing applications). Therefore, for

the OFF condition, the following conditions apply:

TRST = low,

EMU0 = high

EMU1/OFF = low

DEVICE TEST PIN

TEST1

Test1 − Reserved for internal use only. This pin must not be connected (NC).

† I = Input, O = Output, Z = High impedance

TMS320VC549 датащи(PDF) 11 Page - Texas Instruments

TMS320VC549 датащи(HTML) 11 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

датащи скачать

ссылки URL