6.2 Storage Conditions (continued)

Applicable before the DMD is installed in the final product

MIN

MAX

UNIT

TDP

Dew Point Temperature

(non-condensing)

See Note(1)

°C

(1)

The DLP2000 DMD is intended for use in well controlled, low dew point environments. Please contact your local TI sales person or TI

distributor representative to determine if this device is suitable for your application and operating environment compared to other DMD

solutions. DLP Products offers a broad portfolio of DMDs suitable for a wide variety of applications.

6.3 ESD Ratings

VALUE

UNIT

V(ESD)

Electrostatic discharge

Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)

±2000

V

(1)

JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.

6.4 Recommended Operating Conditions

Over operating free-air temperature range (unless otherwise noted)

MIN

NOM

MAX

UNIT

Supply Voltage

VCC

LVCMOS logic power supply voltage(1)

1.65

1.8

1.95

V

VOFFSET

Mirror electrode and HVCMOS voltage(1)

8.25

8.5

8.75

V

VBIAS

Mirror electrode voltage

15.5

16

16.5

V

Supply voltage delta |VBIAS – VOFFSET| (2)

8.75

V

VRESET

Mirror electrode voltage

–9.5

–10

–10.5

V

Input Voltage

VP

Positive going threshold voltage

0.4*VCC

0.7*VCC

V

VN

Negative going threshold voltage

0.3*VCC

0.6*VCC

V

VH

Hysteresis voltage (Vp – Vn)

0.1*VCC

0.4*VCC

V

Environmental

TARRAY

Array temperature—long-term operational(3) (4) (5) (6)

0

40 to 70

°C

Array Temperature – short-term operational(4) (7)

–20

75

°C

|TDELTA|

Absolute temperature difference between any point on

the window edge and the ceramic test point TP1(8)

15

°C

TWINDOW

Window temperature—operational(3) (9)

90

°C

TDP

Dew point temperature (non-condensing)

See

note(10) .

°C

ILLUV

Illumination wavelength < 400 nm(3)

0.68

mW/cm2

ILLVIS

Illumination wavelengths between 400 nm and 700 nm

Thermally limited

ILLIR

Illumination wavelength > 700 nm

10

mW/cm2

(1)

All voltage values are with respect to GND (VSS). VOFFSET, VCC, VBIAS, VRESET , and VSS power supplies are required for the normal

DMD operating mode.

(2)

To prevent excess current, the supply voltage delta |VBIAS – VOFFSET| must be less than 8.75 V.

(3)

Simultaneous exposure of the DMD to the maximum Recommended Operating Conditions for temperature and UV illumination

reduces device lifetime.

(4)

The array temperature cannot be measured directly and must be computed analytically from the temperature measured at test point 1

(TP1) shown in Figure 7-1 and the package thermal resistance in Section 7.6.

(5)

Per Figure 6-1, the maximum operational array temperature should be derated based on the micromirror landed duty cycle that the

DMD experiences in the end application. Refer to Section 7.7 for a definition of micromirror landed duty cycle.

(6)

Long-term is defined as the usable life of the device

(7)

Array temperatures beyond those specified as long-term are recommended for short-term conditions only (power-up). Short-term is

defined as cumulative time over the usable life of the device and is less than 500 hours for temperatures between the long-term

maximum and 75°C, and less than 500 hours for temperatures between 0°C and –20°C.

(8)

Temperature delta is the highest difference between the ceramic test point 1 (TP1) and anywhere on the window edge as shown in

Figure 7-1.

(9)

Window temperature is the highest temperature on the window edge shown in Figure 7-1.

(10) The DLP2000 DMD is intended for use in well controlled, low dew point environments. Please contact your local TI sales person or

TI distributor representative to determine if this device is suitable for your application and operating environment compared other DMD

solutions. DLP Products offers a broad portfolio of DMDs suitable for a wide variety of applications.

www.ti.com

DLP2000

DLPS140B – MARCH 2019 – REVISED MAY 2022

Copyright © 2022 Texas Instruments Incorporated

Submit Document Feedback

7

Product Folder Links: DLP2000