LP5523 datasheet(29/61 Pages) TI2

29 / 61 page

LP5523

www.ti.com

SNVS550E – SEPTEMBER 2009 – REVISED JANUARY 2017

Product Folder Links: LP5523

Submit Documentation Feedback

Table 3. Control Register Map (continued)

HEX

ADDRESS

BIT(s)

READ/

WRITE

DEFAULT VALUE

AFTER RESET

BIT MNEMONIC AND DESCRIPTION

GAIN CHANGE CTRL

[7:6]

R/W

00xxxxxx

THRESHOLD

Threshold voltage (typical)

00 – 400 mV

01 – 300 mV

10 – 200 mV

11 – 100 mV

[5]

R/W

xx0xxxxx

ADAPTIVE_THRESH_EN

Activates adaptive threshold.

[4:3]

R/W

xxx00xxx

TIMER

00 – 5 ms

01 – 10 ms

10 – 50 ms

11 – Infinite

[2]

R/W

xxxxx0xx

FORCE_1x

Activates 1.5× to 1× timer.

7.6.2 Control Register Details

00 ENABLE/ ENGINE CONTROL1

•

00 - Bit [6] CHIP_EN

–

1 = internal start-up sequence powers up all the needed internal blocks and the device enters normal

mode.

–

0 = standby mode is entered. Control registers can still be written or read, excluding bits[5:0] in reg 00

(this register), registers 16h to 1E (LED PWM registers) and 37h to 39h (program counters).

•

00 — Bits [5:4] ENGINE1_EXEC

–

Engine 1 program execution control. Execution register bits define how the program is executed. Program

start address can be programmed to Program Counter (PC) register 37H.

–

00 = hold: Hold causes the execution engine to finish the current instruction and then stop. Program

counter (PC) can be read or written only in this mode.

–

01 = step: Execute the instruction at the location pointed by the PC, increment the PC by one and then

reset ENG1_EXEC bits to 00 (i.e. enter hold).

–

10 = free run: Start program execution from the location pointed by the PC.

–

11 = execute once: Execute the instruction pointed by the current PC value and reset ENG1_EXEC to 00

(that is, enter hold). The difference between step and execute once is that execute once does not

increment the PC.

•

00 — Bits [3:2] ENGINE2_EXEC

–

Engine 2 program execution control. Equivalent to above definition of control bits. Program start address

can be programmed to PC register 38H.

•

00 — Bits [1:0] ENGINE3_EXEC

–

Engine 3 program execution control. Equivalent to engine 1 control bits. Program start address can be

programmed to PC register 39H.

01 ENGINE CONTROL2

•

Operation modes are defined in this register.

–

Disabled: Engines can be configured to disabled mode each one separately.

–

Load program: Writing to program memory is allowed only when the engine is in load program operation

mode and engine busy bit (reg 3A) is not set. Serial bus master should check the busy bit before writing to

program memory or allow at least 1ms delay after entering to load mode before memory write, to ensure

initalization. All the three engines are in hold while one or more engines are in load program mode. PWM

values are frozen, also. Program execution continues when all the engines are out of load program mode.

Load program mode resets the program counter of the respective engine. Load program mode can be

entered from the disabled mode only. Entering load program mode from the run program mode is not

allowed.

LP5523 датащи(PDF) 29 Page - Texas Instruments

LP5523 датащи(HTML) 29 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61

датащи скачать

ссылки URL