| поискавой системы для электроныых деталей |
|
TMP86FS28DFG датащи(PDF) 262 Page - Toshiba Semiconductor |
|
|
|||||||||||||||||||||||||||||
TMP86FS28DFG датащи(HTML) 262 Page - Toshiba Semiconductor |
|
262 / 272 page ![]() Page 250 20. Electrical Characteristics 20.2 Operating Condition TMP86FS28DFG 20.2 Operating Condition The Operating Conditions show the conditions under which the device be used in order for it to operate normally while maintaining its quality. If the device is used outside the range of Operating Conditions (power supply voltage, operating temperature range, or AC/DC rated values), it may operate erratically. Therefore, when designing your application equipment, always make sure its intended working conditions will not exceed the range of Operating Conditions. 20.2.1 MCU mode (Flash Programming or erasing) 20.2.2 MCU mode (Except Flash Programming or erasing) Note 1: When the supply voltage is VDD < 3.0V, the operating tempreture is Topr= -20 to 85 °C. (VSS = 0 V, Topr = -10 to 40°C) Parameter Symbol Pins Ratings Min Max Unit Supply voltage VDD NORMAL1, 2 modes 4.5 5.5 V Input high level VIH1 Except hysteresis input VDD ≥ 4.5 V VDD × 0.70 VDD VIH2 Hysteresis input VDD × 0.75 Input low level VIL1 Except hysteresis input VDD ≥ 4.5 V 0 VDD × 0.30 VIL2 Hysteresis input VDD × 0.25 Clock frequency fc XIN, XOUT 1.0 16.0 MHz (VSS = 0 V, Topr = −40 to 85°C) Parameter Symbol Pins Condition Min Max Unit Supply voltage VDD fc = 16 MHz NORMAL1, 2 mode 4.0 5.5 V IDLE0, 1, 2 mode fc = 8 MHz NORMAL1, 2 mode 2.7(Note1) IDLE0, 1, 2 mode fs = 32.768 kHz SLOW1, 2 mode SLEEP0, 1, 2 mode STOP mode Input high level VIH1 Except hysteresis input VDD ≥ 4.5 V VDD × 0.70 VDD VIH2 Hysteresis input VDD × 0.75 VIH3 VDD < 4.5 V VDD × 0.90 Input low level VIL1 Except hysteresis input VDD ≥ 4.5 V 0 VDD × 0.30 VIL2 Hysteresis input VDD × 0.25 VIL3 VDD < 4.5 V VDD × 0.10 Clock frequency fc XIN, XOUT VDD = 2.7 V to 5.5 V 1.0 8.0 MHz VDD = 4.0 V to 5.5 V 16.0 fs XTIN, XTOUT VDD = 2.7 V to 5.5 V 30.0 34.0 kHz LCD reference voltage range V1 LCD booster circuit enable (V3 ≥ VDD) 0.9 1.8 V Capacity for LCD booster circuit CLCD 0.1 0.47 uF |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |