TSB41AB2PAPR datasheet(20/50 Pages) TI

20 / 50 page

TSB41AB2, TSB41AB2I

IEEE 1394a2000 TWOPORT CABLE

TRANSCEIVER/ARBITER

SLLS424G − JUNE 2000 − REVISED DECEMBER 2004

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

APPLICATION INFORMATION

crystal selection (continued)

The layout of the crystal portion of the PHY circuit is important for obtaining the correct frequency, minimizing

noise introduced into the PHY phase-lock loop, and minimizing any emissions from the circuit. The crystal and

two load capacitors should be considered as a unit during layout. The crystal and load capacitors should be

placed as close as possible to one another while minimizing the loop area created by the combination of the

three components. Varying the size of the capacitors may help in this. Minimizing the loop area minimizes the

effect of the resonant current (Is) that flows in this resonant circuit. This layout unit (crystal and load capacitors)

should then be placed as close as possible to the PHY XI and XO terminals to minimize trace lengths. Figure 11

depicts a layout that meets these guidelines.

C10

Figure 11. Recommended Crystal and Capacitor Layout

It is strongly recommended that part of the verification process for the design be to measure the frequency of

the SYSCLK output of the PHY. This should be done with a frequency counter with an accuracy of six digits or

better. If the SYSCLK frequency is more than the crystal tolerance from 49.152 MHz, the load capacitance of

the crystal may be varied to improve frequency accuracy. If the frequency is too high, add more load

capacitance; if the frequency is too low, decrease load capacitance. Typically, changes should be done to both

load capacitors (C9 and C10 above) at the same time, and both should be of the same value. Additional design

details and requirements may be provided by the crystal vendor. For more information, see Selection and

Specification of Crystals for Texas Instruments IEEE 1394 Physical Layers, TI literature number SLLA051.

EMI guidelines

For electromagnetic interference (EMI) guidelines and recommendations, send a request via email to:

1394-EMI@list.ti.com

designing with the PowerPAD package

The TSB41AB2 is housed in a high performance, thermally enhanced, 64-terminal PAP PowerPAD package.

Use of the PowerPAD package does not require any special considerations except to note that the PowerPAD,

which is an exposed metallic pad on the bottom of the device, is a thermal and electrical conductor. This exposed

pad is connected inside the package to the substrate of the silicon die, it is not connected to any terminal of the

package. Therefore, if not implementing PowerPAD PCB features, the use of solder masks (or other assembly

techniques) may be required to prevent any inadvertent shorting by the exposed PowerPAD of connection

etches or vias under the package. The recommended option, however, is to not run any etches or signal vias

under the device, but to have only a grounded thermal land as explained below. Although the actual size of the

exposed die pad may vary, the minimum size required for the keep-out area of the 64-terminal PAP PowerPAD

package is 8 mm

× 8 mm.

It is recommended that there be a thermal land, which is an area of solder-tinned-copper (see Figure 12),

underneath the PowerPAD package. The thermal land varies in size depending on the PowerPAD package

being used, the PCB construction, and the amount of heat that needs to be removed. In addition, the thermal

land may or may not contain numerous thermal vias depending on PCB construction.

TSB41AB2PAPR датащи(PDF) 20 Page - Texas Instruments

TSB41AB2PAPR датащи(HTML) 20 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

датащи скачать

ссылки URL