SPC58ECX datasheet(146/153 Pages) STMICROELECTRONICS

146 / 153 page

Revision history

SPC584Cx, SPC58ECx

146/153

DS11620 Rev 8

04-Feb-2018

4 (Cont’)

Table 22: External 40 MHz oscillator electrical specifications

Changed table footnote 3 by: This value is determined by the crystal manufacturer

and board design, and it can potentially be higher than the maximum provided.

Table 23: 32 kHz External Slow Oscillator electrical specifications

: Updated the

parameter symbols and added “CC” to Tsxosc.

Table 26: ADC pin specification

– Updated Max value for CS and CP2

– Added electrical specification for R20KΩ symbol

– Changed Max value = 1 by 2 for Cp2 SARB channels

Table 27: SARn ADC electrical specification

– Added symbols tADCINIT and tADCBIASINIT

– Column “C” splitted and added “D” for IADV_S

Table 28: ADC-Comparator electrical specification

– Added new parameter “tADCINITSBY”.

– Set min = 5/fADCK µs with footnote “In case the ADC is used as Fast Comparator

the sampling time is tADCSAMPLE = 2/fADCK”

– Set min = 6/fADCK for ADC comparator mode, at symbol tADCSAMPLE

– Column “C” splitted and added “D” for IADV_S

Section 4.14: LFAST pad electrical characteristics

: Introduction paragraph:

– 1st sentence: hidden text “both the SIPI and”

– all 2nd sentence hidden: “The same LVDS.. tables”

Figure 9: LFAST LVDS timing definition

: Added conditional tag to hide:

– 400 mV p-p (MSC/DSPI)

– 0.50 * T (MSC/DSPI)

– (MSC/DSPI)

Figure 17: Voltage monitor threshold definition

: Right blue line adjusted on the top

figure

Section 4.15.1: Power management integration

: added sentence “It is

recommended...device itself” for all devices

Table 35: Linear regulator specifications

: updated values for symbol “

ΔIDDMREG”

Table 34: External components integration

: Updated Min and Max values at symbol

CE to 1.1 and 3.0 respectively

Table 40: Wait State configuration

: Updated this table by adding APC parameter

and frequency ranges

Section 4.17.5: CAN timing

: added section

Table 57: TxEN output characteristics

: added table footnote “Pad configured as

VERY STRONG.

Table 58: TxD output characteristics

: changed note 3 to apply to the whole table

Table 60: CAN timing

: added columns for “CC” and “D”

Table 82. Document revision history (continued)

Date

Revision

Changes

SPC58ECX датащи(PDF) 146 Page - STMicroelectronics

SPC58ECX датащи(HTML) 146 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL