TMS320F28076PZP datasheet(10/192 Pages) TI

10 / 192 page

6.2 Signal Descriptions

Section 6.2.1 describes the signals. The GPIO function is the default at reset, unless otherwise mentioned. The

peripheral signals that are listed under them are alternate functions. Some peripheral functions may not be

available in all devices. See Table 5-1 for details. All GPIO pins are I/O/Z and have an internal pullup, which can

be selectively enabled or disabled on a per-pin basis. This feature only applies to the GPIO pins. The pullups are

not enabled at reset.

6.2.1 Signal Descriptions

TERMINAL

I/O/Z

(1)

DESCRIPTION

NAME

MUX

POSITION

PTP

NO.

PZP

NO.

ADC, DAC, AND COMPARATOR SIGNALS

VREFHIA

ADC-A high reference. This voltage must be driven into the

pin from external circuitry. Place at least a 1-µF capacitor on

this pin. This capacitor should be placed as close to the

device as possible between the VREFHIA and VREFLOA pins.

NOTE: Do not load this pin externally.

VREFHIB

ADC-B high reference. This voltage must be driven into the

pin from external circuitry. Place at least a 1-µF capacitor on

this pin. This capacitor should be placed as close to the

device as possible between the VREFHIB and VREFLOB pins.

NOTE: Do not load this pin externally.

VREFHID

–

ADC-D high reference. This voltage must be driven into the

pin from external circuitry. Place at least a 1-µF capacitor on

this pin. This capacitor should be placed as close to the

device as possible between the VREFHID and VREFLOD pins.

NOTE: Do not load this pin externally.

VREFLOA

ADC-A low reference.

On the PZP package, pin 17 is double-bonded to VSSA and

VREFLOA. On the PZP package, pin 17 must be connected to

VSSA on the system board.

VREFLOB

ADC-B low reference

VREFLOD

–

ADC-D low reference

ADCIN14

Input 14 to all ADCs. This pin can be used as a general-

purpose ADCIN pin or it can be used to calibrate all ADCs

together from an external reference.

CMPIN4P

Comparator 4 positive input

ADCIN15

Input 15 to all ADCs. This pin can be used as a general-

purpose ADCIN pin or it can be used to calibrate all ADCs

together from an external reference.

CMPIN4N

Comparator 4 negative input

ADCINA0

ADC-A input 0. There is a 50-kΩ internal pulldown on this pin

in both an ADC input or DAC output mode which cannot be

disabled.

DACOUTA

DAC-A output

ADCINA1

ADC-A input 1. There is a 50-kΩ internal pulldown on this pin

in both an ADC input or DAC output mode which cannot be

disabled.

DACOUTB

DAC-B output

ADCINA2

ADC-A input 2

CMPIN1P

Comparator 1 positive input

ADCINA3

ADC-A input 3

CMPIN1N

Comparator 1 negative input

ADCINA4

ADC-A input 4

CMPIN2P

Comparator 2 positive input

TMS320F28076, TMS320F28075

SPRS902J – OCTOBER 2014 – REVISED FEBRUARY 2021

www.ti.com

Submit Document Feedback

Product Folder Links: TMS320F28076 TMS320F28075

TMS320F28076PZP датащи(PDF) 10 Page - Texas Instruments

TMS320F28076PZP датащи(HTML) 10 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL