PCI6621 datasheet(85/204 Pages) TI

85 / 204 page

4−9

4.14 Secondary Status Register

The secondary status register is compatible with the PCI-PCI bridge secondary status register. It indicates

CardBus-related device information to the host system. This register is very similar to the PCI status register (PCI

offset 06h, see Section 4.5), and status bits are cleared by a writing a 1. This register is not shared by the two socket

functions, but is accessed on a per-socket basis. See Table 4−5 for a complete description of the register contents.

Bit

Name

Secondary status

Type

Default

Secondary status

Offset:

16h

Type:

Read-only, Read/Clear

Default:

0200h

Table 4−5. Secondary Status Register Description

BIT

SIGNAL

TYPE

FUNCTION

15 ‡

CBPARITY

Detected parity error. This bit is set when a CardBus parity error is detected, either an address or data

parity error. Write a 1 to clear this bit.

14 ‡

CBSERR

Signaled system error. This bit is set when CSERR is signaled by a CardBus card. The PCI6x21/PCI6x11

controller does not assert the CSERR signal. Write a 1 to clear this bit.

13 ‡

CBMABORT

Received master abort. This bit is set when a cycle initiated by the PCI6x21/PCI6x11 controller on the

CardBus bus is terminated by a master abort. Write a 1 to clear this bit.

12 ‡

REC_CBTA

Received target abort. This bit is set when a cycle initiated by the PCI6x21/PCI6x11 controller on the

CardBus bus is terminated by a target abort. Write a 1 to clear this bit.

11 ‡

SIG_CBTA

Signaled target abort. This bit is set by the PCI6x21/PCI6x11 controller when it terminates a transaction

on the CardBus bus with a target abort. Write a 1 to clear this bit.

10−9

CB_SPEED

CDEVSEL timing. These bits encode the timing of CDEVSEL and are hardwired to 01b indicating that the

PCI6x21/PCI6x11 controller asserts this signal at a medium speed.

8 ‡

CB_DPAR

CardBus data parity error detected. Write a 1 to clear this bit.

0 = The conditions for setting this bit have not been met.

1 = A data parity error occurred and the following conditions were met:

a. CPERR was asserted on the CardBus interface.

b. The PCI6x21/PCI6x11 controller was the bus master during the data parity error.

c. The parity error response enable bit (bit 0) is set in the bridge control register (PCI offset 3Eh,

see Section 4.25).

CBFBB_CAP

Fast back-to-back capable. The PCI6x21/PCI6x11 controller cannot accept fast back-to-back

transactions; therefore, this bit is hardwired to 0.

CB_UDF

User-definable feature support. The PCI6x21/PCI6x11 controller does not support user-definable

features; therefore, this bit is hardwired to 0.

CB66MHZ

66-MHz capable. The PCI6x21/PCI6x11 CardBus interface operates at a maximum CCLK frequency of

33 MHz; therefore, this bit is hardwired to 0.

4−0

RSVD

These bits return 0s when read.

‡ One or more bits in this register are cleared only by the assertion of GRST.

PCI6621 датащи(PDF) 85 Page - Texas Instruments

PCI6621 датащи(HTML) 85 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL