www.ti.com

ABSOLUTE MAXIMUM RATINGS

CDCM7005

SCAS793A – JUNE 2005 – REVISED JUNE 2005

Table 1. PIN ASSINGMENT (continued)

TERMINAL

I/O

DESCRIPTION

NAME

BGA

QFN

Bias voltage output to be used to bias unused complementary input VCXO_IN for

VBB

C1

40

O

limited to about 1.5 mA.

This output can be programmed (SPI) to provide either the STATUS_REF or

PRI_SEC_CLK information. This pin is set high if one of the STATUS conditions is

valid. STATUS_REF is the default setting.

STATUS_REF or

In case of STATUS_REF, the LVCMOS output provides the Status of the

C8

23

O

PRI_SEC_CLK

Reference Clock. If a reference clock with a frequency above 2 MHz is provided to

PRI_REF or SEC_REF STATUS_REF will be set high.

In case of PRI_SEC_CLK, the LVCMOS output indicates whether the primary

clock [high] or the secondary clock [low] is selected.

This LVCMOS output can be programmed (SPI) to provide either the

STATUS_VCXO information or serve as current path for the charge pump (CP).

STATUS_VCXO is the default setting.

In case of STATUS_VCXO, the LVCMOS output provides the status of the VCXO

STATUS_VCXO

D8

22

O

input (frequencies above 2 MHz are interpreted as valid clock; active high).

or I_REF_CP

In case of I_REF_CP, it provides the current path for the external reference

resistor (12 k

Ω± 1%) to support an accurate charge pump current, optional. Do not

use any capacitor across this resistor to prevent noise coupling via this node. If

the internal 12 k

Ω is selected (default setting), this pin can be left open.

LVCMOS output for PLL_LOCK information. This pin is set high if the PLL is in

lock (see feature description). This output can be programmed to be digital lock

detect or analog lock detect (see feature description).

The PLL is locked (set high), if the rising edge either of PRI_REF or SEC_REF

clock and VCXO_IN clock at the phase frequency detector (PFD) are inside the

lock detect window for a predetermined number of successive clock cycles.

PLL_LOCK

A8

25

I/O

The PLL is out-of-lock (set low), if the rising edge of either the PRI_REF or

SEC_REF) clock and VCXO_IN clock at the PFD are outside the lock detect

window or if a cycle-slip occurs.

Both, the lock detect window and the number of successive clock cycles are user

definable (via SPI).

Y0A:Y0B

F1, G1,

46, 47,

The outputs of the CDCM7005 are user definable and can be any combination of

Y1A:Y1B

H2, H3,

3, 4,

up to five LVPECL outputs or up to 10 LVCMOS outputs. The outputs are

Y2A:Y2B

H4, H5,

7, 8,

O

selectable via SPI (Word 1, Bit 2-6). The power-up setting is all outputs are

Y3A:Y3B

H6, H7,

11,12,

LVPECL.

Y4A:Y4B

G8, F8

16, 17

VALUE / UNIT

–0.5 V to 4.6 V

Output current for LVPECL/LVCMOS outputs

±50 mA

±20 mA

Storage temperature range

–65

°C to 150°C

Maximum junction temperature

125

°C

(1)

Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings

only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating

conditions is not implied. Exposure to absolute–maximum–rated conditions for extended periods may affect device reliability.

(2)

All supply voltages have to be supplied at the same time.

(3)

The input and output negative voltage ratings may be exceeded if the input and output clamp-current ratings are observed.

5