AT89C51ED2-RDTIM datasheet(12/137 Pages) ATMEL

12 / 137 page

AT89C51RD2/ED2

4235E–8051–04/04

I/O

P1.7: Input/Output:

I/O

CEX4: Capture/Compare External I/O for PCA module 4

I/O

MOSI: SPI Master Output Slave Input line

When SPI is in master mode, MOSI outputs data to the slave peripheral.

When SPI is in slave mode, MOSI receives data from the master control-

ler.

XTALA1

XTALA 1: Input to the inverting oscillator amplifier and input to the inter-

nal clock generator circuits.

XTALA2

XTALA 2: Output from the inverting oscillator amplifier

P2.0 - P2.7

24 - 31

18 - 25

54, 55,

56, 58,

59, 61,

64, 65

43, 44,

45, 47,

48, 50,

53, 54

I/O

Port 2: Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2

pins that have 1s written to them are pulled high by the internal pull-ups

and can be used as inputs. As inputs, Port 2 pins that are externally

pulled low will source current because of the internal pull-ups. Port 2

emits the high-order address byte during fetches from external program

memory and during accesses to external data memory that use 16-bit

addresses (MOVX @DPTR).In this application, it uses strong internal

pull-ups emitting 1s. During accesses to external data memory that use

8-bit addresses (MOVX @Ri), port 2 emits the contents of the P2 SFR.

21-28

P3.0 - P3.7

11,

13 - 19

7 - 13

34, 39,

40, 41,

42, 43,

45, 47

25, 28,

29, 30,

31, 32,

34, 36

10-17

I/O

Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3

pins that have 1s written to them are pulled high by the internal pull-ups

and can be used as inputs. As inputs, Port 3 pins that are externally

pulled low will source current because of the internal pull-ups. Port 3 also

serves the special features of the 80C51 family, as listed below.

5342510

RXD (P3.0): Serial input port

73928

TXD (P3.1): Serial output port

8402912

INT0 (P3.2): External interrupt 0

9413013

INT1 (P3.3): External interrupt 1

T0 (P3.4): Timer 0 external input

T1 (P3.5): Timer 1 external input

WR (P3.6): External data memory write strobe

RD (P3.7): External data memory read strobe

P4.0 - P4.7

20, 24,

26, 44,

46, 50,

53, 57

11, 15,

17,33,

35,39,

42, 46

-I/O

Port 4: Port 4 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3

pins that have 1s written to them are pulled high by the internal pull-ups

and can be used as inputs. As inputs, Port 3 pins that are externally

pulled low will source current because of the internal pull-ups.

P5.0 - P5.7

60, 62,

63, 7, 8,

10, 13,

49, 51,

52, 62,

63, 1, 4,

-I/O

Port 5: Port 5 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3

pins that have 1s written to them are pulled high by the internal pull-ups

and can be used as inputs. As inputs, Port 3 pins that are externally

pulled low will source current because of the internal pull-ups.

RST

Reset: A high on this pin for two machine cycles while the oscillator is

running, resets the device. An internal diffused resistor to VSS permits a

power-on reset using only an external capacitor to V

CC. This pin is an out-

put when the hardware watchdog forces a system reset.

Table 13. Pin Description (Continued)

Mnemonic

Pin Number

Type

Name and Function

PLCC44 VQFP44

PLCC68

VQFP64

PDIL40

AT89C51ED2-RDTIM датащи(PDF) 12 Page - ATMEL Corporation

AT89C51ED2-RDTIM датащи(HTML) 12 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL