| поискавой системы для электроныых деталей |
|
MFC2000 датащи(PDF) 153 Page - List of Unclassifed Manufacturers |
|
|
|||||||||||||||||||||||||||||
MFC2000 датащи(HTML) 153 Page - List of Unclassifed Manufacturers |
|
153 / 426 page ![]() Hardware Description MFC 2000 Multifunctional Peripheral Controller 2000 100723A Conexant 7-5 Bit 15-8 Shift Enable[7:0] These bits are used to shift scanner controller signals by ½ ihsclk. By default, all scanner controller signals are synchronized to the rising edge of ihsclk. By setting this bit, the corresponding scanner controller signal will be shifted by ½ ihsclk, i.e., it will be synchronized to the falling edge of ihsclk. ShiftEnb[7]: to shift ‘sample’ signal ShiftEnb[6:1]: to shift ‘scctrl[6:1]’ signals ShiftEnb[0]: to shift ‘clamp’ signal Bit 2 VSC on EV bus When this bit is set, the “EV_VD[5:0]” bus will be turned into output with the following signals on the bus: EV_VD[5:0] Output signals 5 ScanIAConfig[5] as GPO 4 ScanIAConfig[4] as GPO 3 sample/clk2d 2 clk1/clk2c 1 clk1/clk2b 0 clamp Bit 1 ihsclk period 0: ihsclk period = sysclk period 1: ihsclk period = sysclk period/2) This bit determines the period of ihsclk (the primary clock of VSC). Bit 0 VSC Mode 0: scanner 1: video This mode will determine the source of data. Name/Address Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Default Scan Cycle (ScanCycle) $01FF8891 (Not Used) (Not Used) (Not Used) MSINT IRQ location Rst. Value xxx11111h Read Value 1Fh Name/Address Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Default Scan Cycle (ScanCycle) $01FF8890 (Not Used) (Not Used) (Not Used) Scan Cycle (n) MSINTs per Scan Cycle = (n+1) Rst. Value xxx00000b Read Value 00h Bits 12-8 MSINT IRQ location The value written here is double-bufferred. At the beginning of a scan cycle, the value will be transferred into another buffer which is compared to a scan cycle counter. If the value in the buffer matches the value in the counter, then an interrupt will be generated (if it is enabled) at the beginning of the count. Bits 4-0 Scan Cycle (n, n = 0-31; MSINTs per scan cycle = n+1) The value written here is double-buffered. At the beginning of a scan cycle, the value will be transferred into another buffer. |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |