CP5.241, CP5.241-C1,

CP5.241-S1, CP5.241-S2

CP-Series

Aug. 2017 / Rev. 0.1 DS-CP5.241-EN

All parameters are typical values specified at 24V, 5A output, 230Vac input, 25°C ambient and

after a 5 minutes run-in time unless otherwise noted.

www.pulspower.com Phone +49 89 9278 0

Germany

14/26

P R E L I M I N A R Y

15. EMC

The power supply is suitable for applications in industrial environment as well as in residential, commercial and light

industry environments.

EMC Immunity

According generic standards: EN 61000-6-1 and EN 61000-6-2

Electrostatic discharge

EN 61000-4-2

contact discharge

air discharge

8kV

15kV

Criterion A

Criterion A

Electromagnetic RF field

EN 61000-4-3

80MHz-2.7GHz

20V/m

Criterion A

Fast transients (Burst)

EN 61000-4-4

input lines

output lines

DC-OK signal (coupling clamp)

4kV

2kV

2kV

Criterion A

Criterion A

Criterion A

Surge voltage on input

EN 61000-4-5

L

N

L

PE, N

PE

2kV

4kV

Criterion A

Criterion A

Surge voltage on output

EN 61000-4-5

+

-

+ / -

PE

1kV

2kV

Criterion A

Criterion A

Surge voltage on DC-OK

EN 61000-4-5

DC-OK signal

PE

1kV

Criterion A

Conducted disturbance

EN 61000-4-6

0.15-80MHz

20V

Criterion A

Mains voltage dips

EN 61000-4-11

0% of 100Vac

40% of 100Vac

70% of 100Vac

0% of 200Vac

40% of 200Vac

70% of 200Vac

0Vac, 20ms

40Vac, 200ms

70Vac, 500ms

0Vac, 20ms

80Vac, 200ms

140Vac, 500ms

Criterion A

Criterion C

Criterion C

Criterion A

Criterion A

Criterion A

Voltage interruptions

EN 61000-4-11

0% of 200Vac (=0V)

5000ms

Criterion C

Voltage sags

SEMI F47 0706

dips on the input voltage according to SEMI F47 standard

80% of 120Vac (96Vac)

70% of 120Vac (84Vac)

50% of 120Vac (60Vac)

1000ms

500ms

200ms

Criterion A

Criterion A

Criterion A

Powerful transients

VDE 0160

over entire load range

750V, 0.3ms

Criterion A

Criterions:

A:

Power supply shows normal operation behavior within the defined limits.

C:

Temporary loss of function is possible. Power supply may shut-down and restarts by itself. No damage or hazards for the power supply

will occur.

EMC Emission

According generic standards: EN 61000-6-3 and EN 61000-6-4

Conducted emission

input lines

EN 55011, EN 55022, FCC Part 15, CISPR 11, CISPR 22

Class B

Conducted emission

IEC/CISPR 16-1-2, IEC/CISPR 16-2-1

Class A

Radiated emission

EN 55011, EN 55022

Class B

Harmonic input current (PFC)

EN 61000-3-2

Class A equipment: fulfilled

Voltage fluctuations, flicker

EN 61000-3-3

This device complies with FCC Part 15 rules.

Operation is subjected to following two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause undesired operation.

*)

tested with constant current loads, non pulsing

**) for information only, not mandatory for EN 61000-6-3