GD25Q32C datasheet(36/50 Pages) ELM

36 / 50 page

Rev.1.0

50 -

http://www.elm-tech.com

GD25Q32CxIGx 3.3V Uniform Sector Dual and Quad Serial Flash

Address

A23-A16

A15-A12

A11-A10

A9-A0

Security Register #1

00H

0 0 0 1

0 0

Byte Address

Security Register #2

00H

0 0 1 0

0 0

Byte Address

Security Register #3

00H

0 0 1 1

0 0

Byte Address

Figure 35. Erase Security Registers command Sequence Diagram

Command

0 1 2 3 4 5 6 7

44H

CS#

SCLK

8 9

29 30 31

MSB

2 1 0

24 Bits Address

23 22

7.31. Program Security Registers (42H)

The Program Security Registers command is similar to the Page Program command. It allows from 1 to 1024

bytes Security Registers data to be programmed. A Write Enable (WREN) command must previously have been

executed to set the Write Enable Latch (WEL) bit before sending the Program Security Registers command. The

Program Security Registers command is entered by driving CS# Low, followed by the command code (42H),

three address bytes and at least one data byte on SI. As soon as CS# is driven high, the self-timed Program

Security Registers cycle (whose duration is tPP) is initiated. While the Program Security Registers cycle is in

progress, the Status Register may be read to check the value of the Write in Progress (WIP) bit. The Write in

Progress (WIP) bit is 1 during the self-timed Program Security Registers cycle, and is 0 when it is completed. At

some unspecified time before the cycle is completed, the Write Enable Latch (WEL) bit is reset.

If the Security Registers Lock Bit (LB3-1) is set to 1, the Security Registers will be permanently locked.

Program Security Registers command will be ignored.

Address

A23-A16

A15-A12

A11-A10

A9-A0

Security Register #1

00H

0 0 0 1

0 0

Byte Address

Security Register #2

00H

0 0 1 0

0 0

Byte Address

Security Register #3

00H

0 0 1 1

0 0

Byte Address

→ CS# goes high. The command sequence is shown in Figure35. CS# must be driven high after the eighth bit

of the command code has been latched in; otherwise the Erase Security Registers command is not executed.

As soon as CS# is driven high, the self-timed Erase Security Registers cycle (whose duration is tSE) is initiated.

While the Erase Security Registers cycle is in progress, the Status Register may be read to check the value of the

Write in Progress (WIP) bit. The Write in Progress (WIP) bit is 1 during the self-timed Erase Security Registers

cycle, and is 0 when it is completed. At some unspecified time before the cycle is completed, the Write Enable

Latch (WEL) bit is reset. The Security Registers Lock Bit (LB3-1) in the Status Register can be used to OTP

protect the security registers. Once the LB bit is set to 1, the Security Registers will be permanently locked; the

Erase Security Registers command will be ignored.

GD25Q32C датащи(PDF) 36 Page - ELM Electronics

GD25Q32C датащи(HTML) 36 Page - ELM Electronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

датащи скачать

ссылки URL