| поискавой системы для электроныых деталей |
|
LM3560TLX/NOPB датащи(PDF) 37 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
LM3560TLX/NOPB датащи(HTML) 37 Page - Texas Instruments |
|
37 / 48 page ![]() LM3560 www.ti.com SNOSB43B – SEPTEMBER 2011 – REVISED AUGUST 2013 Table 17. Flags Register Descriptions (continued) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (VIN Monitor) (VIN Flash (NTC Fault) (TX2 (TX1 Interrupt ) (LED Fault) (Thermal (Flash Time- Monitor) Interrupt) Shutdown) out) 1 = VIN 1 = VIN Flash 1 = NTC mode 1 = TX2 has 1 = TX1 has 1 = LED Failed 1 = Die 1 = Flash Time- Monitor is Monitor is is enabled and changed state changed state (Open or Temperature Out Expired enabled and enabled and LEDI/NTC has (TX2 mode (TX1 mode only) Short) has crossed VIN has fallen VIN fell below fallen below 1V only) the Thermal below the the Shutdown programmed programmed Threshold threshold VIN Flash Monitor threshold during flash pulse turn-on CONFIGURATION REGISTER 1 (Address 0xE0) Configuration Register 1 holds the STROBE Enable bit, the STROBE polarity bit, the NTC Enable bit, the polarity selection bit for TX1 and TX2, and the Hardware Torch Enable bit (see Table 18). Table 18. Configuration Register 1 Descriptions Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (Hardware (TX2 Polarity) (TX1 Polarity) (NTC Mode (STROBE (STROBE (Not Used) (Not Used) Torch Mode Enable) Polarity) Input Enable) Enable) 0 = 0 = TX2 is 0 = TX1 is 0 = LEDI/NTC 0 = STROBE 0 = STROBE N/A N/A TX1/TORCH is configured for configured for pin is Input Enable is Input Disabled a TX active low active low configured as active low. (Default) input(default) polarity polarity an indicator Pulling output (default) STROBE low will turn on Flash current 1 = 1 =TX2 pin is 1 = TX1 is 1 = LEDI/NTC 1 = STROBE 1 = STROBE TX1/TORCH configured for configured for is configured as Input is active Input Enabled pin is a active high active high a comparator high. Pulling hardware polarity polarity input for an STROBE high TORCH (default) (default) NTC thermistor will turn on enable. This bit Flash current is reset to 0 (default) after a flash pulse. Copyright © 2011–2013, Texas Instruments Incorporated Submit Documentation Feedback 37 Product Folder Links: LM3560 |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |