PIC17C44-08SLASHP datasheet(108/240 Pages) MICROCHIP

108 / 240 page

PIC17C4X

DS30412C-page 108

Table 15-2 lists the instructions recognized by the

MPASM assembler.

All instruction examples use the following format to rep-

resent a hexadecimal number:

0xhh

where h signiﬁes a hexadecimal digit.

To represent a binary number:

0000 0100b

where b signiﬁes a binary string.

FIGURE 15-1: GENERAL FORMAT FOR

INSTRUCTIONS

Note 1: Any unused opcode is Reserved. Use of

any reserved opcode may cause unex-

pected operation.

Note 2: The shaded instructions are not available

in the PIC17C42

Byte-oriented ﬁle register operations

d = 0 for destination WREG

OPCODE

f (FILE #)

d = 1 for destination f

f = 8-bit ﬁle register address

Bit-oriented ﬁle register operations

11 10

8 7

OPCODE

b (BIT #)

f (FILE #)

b = 3-bit address

f = 8-bit ﬁle register address

Literal and control operations

OPCODE

k (literal)

k = 8-bit immediate value

Byte to Byte move operations

13 12

8 7

OPCODE

p (FILE #)

f (FILE #)

Call and GOTO operations

13 12

OPCODE

k (literal)

k = 13-bit immediate value

p = peripheral register ﬁle address

f = 8-bit ﬁle register address

15.1

Special Function Registers as

Source/Destination

The PIC17C4X’s orthogonal instruction set allows read

and write of all ﬁle registers, including special function

registers. There are some special situations the user

should be aware of:

15.1.1

ALUSTA AS DESTINATION

If an instruction writes to ALUSTA, the Z, C, DC and OV

bits may be set or cleared as a result of the instruction

and overwrite the original data bits written. For exam-

ple, executing CLRF

ALUSTA

will clear register

ALUSTA, and then set the Z bit leaving 0000 0100b in

the register.

15.1.2

PCL AS SOURCE OR DESTINATION

Read, write or read-modify-write on PCL may have the

following results:

Read PC:

PCH

→ PCLATH; PCL → dest

Write PCL:

PCLATH

→ PCH;

8-bit destination value

→ PCL

Read-Modify-Write:

PCL

→ ALU operand

PCLATH

→ PCH;

8-bit result

→ PCL

Where PCH = program counter high byte (not an

addressable register), PCLATH = Program counter

high holding latch, dest = destination, WREG or f.

15.1.3

BIT MANIPULATION

All bit manipulation instructions are done by ﬁrst read-

ing the entire register, operating on the selected bit and

writing the result back (read-modify-write). The user

should keep this in mind when operating on special

function registers, such as ports.

PIC17C44-08/P датащи(PDF) 108 Page - Microchip Technology

PIC17C44-08/P датащи(HTML) 108 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL