PIC17C44-08SLASHP datasheet(93/240 Pages) MICROCHIP

93 / 240 page

DS30412C-page 93

PIC17C4X

13.3

USART Synchronous Master Mode

In Master Synchronous mode, the data is transmitted in

a half-duplex manner; i.e. transmission and reception

do not occur at the same time: when transmitting data,

the reception is inhibited and vice versa. The synchro-

nous

mode

entered

setting

the

SYNC

(TXSTA<4>) bit. In addition, the SPEN (RCSTA<7>) bit

is set in order to conﬁgure the RA5 and RA4 I/O ports

to CK (clock) and DT (data) lines respectively. The

Master mode indicates that the processor transmits the

master clock on the CK line. The Master mode is

entered by setting the CSRC (TXSTA<7>) bit.

13.3.1

USART SYNCHRONOUS MASTER

TRANSMISSION

The USART transmitter block diagram is shown in

Figure 13-3. The heart of the transmitter is the transmit

(serial) shift register (TSR). The shift register obtains its

data from the read/write transmit buffer TXREG.

TXREG is loaded with data in software. The TSR is not

loaded until the last bit has been transmitted from the

previous load. As soon as the last bit is transmitted, the

TSR is loaded with new data from TXREG (if available).

Once TXREG transfers the data to the TSR (occurs in

one TCY at the end of the current BRG cycle), TXREG

is empty and the TXIF (PIR<1>) bit is set. This interrupt

can be enabled/disabled by setting/clearing the TXIE

bit (PIE<1>). TXIF will be set regardless of the state of

bit TXIE and cannot be cleared in software. It will reset

only when new data is loaded into TXREG. While TXIF

indicates the status of TXREG, TRMT (TXSTA<1>)

shows the status of the TSR. TRMT is a read only bit

which is set when the TSR is empty. No interrupt logic

is tied to this bit, so the user has to poll this bit in order

to determine if the TSR is empty. The TSR is not

mapped in data memory, so it is not available to the

user.

Transmission

enabled

setting

the

TXEN

(TXSTA<5>) bit. The actual transmission will not occur

until TXREG has been loaded with data. The ﬁrst data

bit will be shifted out on the next available rising edge

of the clock on the RA5/TX/CK pin. Data out is stable

around the falling edge of the synchronous clock

(Figure 13-10). The transmission can also be started

by ﬁrst loading TXREG and then setting TXEN. This is

advantageous when slow baud rates are selected,

since BRG is kept in RESET when the TXEN, CREN,

and SREN bits are clear. Setting the TXEN bit will start

the BRG, creating a shift clock immediately. Normally

when transmission is ﬁrst started, the TSR is empty, so

a transfer to TXREG will result in an immediate transfer

the

TSR,

resulting

empty

TXREG.

Back-to-back transfers are possible.

Clearing TXEN during a transmission will cause the

transmission to be aborted and will reset the transmit-

ter. The RA4/RX/DT and RA5/TX/CK pins will revert to

hi-impedance. If either CREN or SREN are set during

a transmission, the transmission is aborted and the

RA4/RX/DT pin reverts to a hi-impedance state (for a

reception). The RA5/TX/CK pin will remain an output if

the CSRC bit is set (internal clock). The transmitter

logic is not reset, although it is disconnected from the

pins. In order to reset the transmitter, the user has to

clear the TXEN bit. If the SREN bit is set (to interrupt an

ongoing transmission and receive a single word), then

after the single word is received, SREN will be cleared

and the serial port will revert back to transmitting, since

the TXEN bit is still set. The DT line will immediately

switch from hi-impedance receive mode to transmit

and start driving. To avoid this, TXEN should be

cleared.

order

select

9-bit

transmission,

the

TX9 (TXSTA<6>) bit should be set and the ninth bit

should be written to TX9D (TXSTA<0>). The ninth bit

must be written before writing the 8-bit data to TXREG.

This is because a data write to TXREG can result in an

immediate transfer of the data to the TSR (if the TSR is

empty). If the TSR was empty and TXREG was written

before writing the “new” TX9D, the “present” value of

TX9D is loaded.

Steps to follow when setting up a Synchronous Master

Transmission:

Initialize the SPBRG register for the appropriate

baud rate (see Baud Rate Generator Section for

details).

Enable the synchronous master serial port by

setting the SYNC, SPEN, and CSRC bits.

Ensure that the CREN and SREN bits are clear

(these bits override transmission when set).

If interrupts are desired, then set the TXIE bit

(the GLINTD bit must be clear and the PEIE bit

must be set).

If 9-bit transmission is desired, then set the TX9

bit.

Start transmission by loading data to the

TXREG register.

If 9-bit transmission is selected, the ninth bit

should be loaded in TX9D.

Enable the transmission by setting TXEN.

Writing the transmit data to the TXREG, then enabling

the transmit (setting TXEN) allows transmission to start

sooner then doing these two events in the reverse

order.

Note:

To terminate a transmission, either clear

the SPEN bit, or the TXEN bit. This will

reset the transmit logic, so that it will be in

the

proper

state

when

transmit

re-enabled.

PIC17C44-08/P датащи(PDF) 93 Page - Microchip Technology

PIC17C44-08/P датащи(HTML) 93 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL