MAX3761CSLASHD datasheet(8/12 Pages) MAXIM

8 / 12 page

Capacitor Selection

A typical MAX3761/MAX3762 implementation requires

four external capacitors. To select the capacitors, first

determine the following parameters in the receiver sys-

tem (see the Applications Information section for rec-

ommendations in 622Mbps ATM and Fibre Channel

1063Mbps systems):

1) The duration of the expected longest run of consec-

utive bits in the data stream. For example, 72 con-

secutive zeros in a 622Mbps data stream have a

duration of 116ns.

2) The maximum allowable data-dependent jitter.

3) The desired power-detector integration time con-

stant [1 / (2

πfINT)].

4) The transimpedance amplifier’s maximum peak-to-

peak output voltage.

Step 1. Select the Input AC-Coupling Capacitors (CIN).

When using a limiting preamplifier with a highpass

frequency response, select CIN to provide a low-

frequency cutoff (fC) one decade lower than the

preamplifier low-frequency cutoff. This causes nearly all

data-dependent jitter (DDJ) to be generated in the pre-

amplifer circuit. For example, if the preamplifier’s low-

frequency cutoff is 150kHz, then select CIN to provide a

15kHz low-frequency cutoff.

Select CIN with the following equation:

For differential input signals, use a capacitor equal to

CIN on both inputs (VIN+ and VIN-). For single-ended

input signals, one capacitor should be tied to VIN+ and

another should decouple VIN- to ground.

When using a preamplifier without a highpass

response, select CIN to ensure that data-dependent jit-

ter is acceptable. The following equation provides an

estimate for CIN:

where: tL = duration of the longest run of consecutive

bits with the same value (seconds); DDJ = maximum

allowable data-dependent jitter, peak-to-peak (seconds);

BW = typical system bandwidth, normally 0.6 to 1.0

times the data rate (hertz).

Regardless of which method is used to select CIN, the

maximum LOS assert time can be estimated from the

value of CIN. The following equation estimates LOS time

delay when the maximum-amplitude signal is instanta-

neously removed from the input, and when the FILTER

time constant is much faster than the input time con-

stant (CFILTER < 0.4CIN):

tLOS ASSERT = 1950CINln(VMAXp-p / VASSERTp-p)

where VMAXp-p is the maximum output of the preampli-

fier, and VASSERTp-p is the input amplitude that causes

LOS to assert. The equation describes the input capac-

itors’ discharge time, from maximum input to the LOS

threshold into the 1950

Ω, single-ended input resis-

tance.

Step 2. Select the Offset-Correction Capacitor (CAZ).

To maintain stability, it is important to keep a one-

decade separation between fC and the low-frequency

cutoff associated with the DC-offset-correction circuit

(fOC).

The input impedance between CZP and CZN is

approximately 800k

Ω in parallel with 10pF. As a result,

the low-frequency cutoff (fOC) associated with the DC-

offset-correction loop is computed as follows:

where CAZ is an optional external capacitor between

CZP and CZN.

If CIN is known, then:

Step 3. Select the Power-Detect Integration Capacitor

(CFILTER). For 622Mbps ATM applications, Maxim rec-

ommends a filter frequency of 3MHz, which requires

CFILTER = 100pF. The integration frequency can be

selected lower to remove low-frequency noise, or to

prevent unusual data sequences from asserting LOS.

CFILTER = 1 / ( 2

π500fINT)

where fINT is the integration frequency.

≥−

2 800k

πΩ CpF

AZ +

()

≥

− ()(

)













DDJ BW

1950

2 f 1950

πΩ

Low-Power, 622Mbps Limiting Amplifiers

with Chatter-Free Power Detect for LANs

_______________________________________________________________________________________

MAX3761C/D датащи(PDF) 8 Page - Maxim Integrated Products

MAX3761C/D датащи(HTML) 8 Page - Maxim Integrated Products

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

датащи скачать

ссылки URL