LTC1400CS8 datasheet(15/20 Pages) LINER

15 / 20 page

LTC1400

TYPICAL APPLICATIONS

TMS320C50 Code for Circuit

THIS PROGRAM DEMONSTRATES LTC1400 INTERFACE TO TMS320C50

FRAME SYNC PULSE IS GENERATED FROM TFSX

*Initialization*

.mmregs

; Defines global symbolic names

;- - Initialized data memory to zero

.ds

0F00h

; Initialize data to zero

DATA0

.word

; Begin sample data location

DATA1

.word

; .

DATA2

.word

; Location of data

DATA3

.word

; .

DATA4

.word

; .

DATA5

.word

; End sample data location

;- - Set up the ISR vector

.ps

080Ah

; Serial ports interrupts

rint :

RECEIVE

; 0A;

xint :

TRANSMIT

; 0C;

trnt :

TREC

; 0E;

txnt :

TTRANX

; 10;

;- - Setup the reset vector

.ps 0A00h

.entry

START:

*TMS32C050 Initialization*

SETC INTM

; Temporarily disable all interrupts

LDP

; Set data page pointer to zero

OPL

#0834h, PMST ; Set up the PMST status and control register

LACC #0

SAMM CWSR

; Set software wait state to 0

SAMM PDWSR

;

*Configure Serial Port*

SPLK #0038h, TSPC ; Set TDM Serial Port

; TDM = 0 Stand Alone mode

; DLB=0 Not loop back

; FO=0 16 Bits

; FSM=1 Burst Mode

; MCM=1 CLKX is generated internally

; TXM=1 FSX as output pin

; Put serial port into reset

; (XRST=RRST=0)

SPLK #00F8h, TSPC

; Take Serial Port out of reset

; (XRST=RRST=1)

SPLK #0FFFFh, IFR

; Clear all the pending interrupts

*Start Serial Communication*

SACL TDXR

; Generate frame sync pulse

SPLK #040h, IMR

; Turn on TRNT receiver interrupt

CLRC INTM

; Enable interrupt

CLRC SXM

; For Unipolar input, set for right shift

; with no sign extension

MAR *AR7

; Load the auxiliary register pointer with seven

LAR

AR7, #0F00h

; Load the auxiliary register seven with #0F00h

; as the begin address for data storage

WAIT:

NOP

; Wait for a receive interrupt

NOP

;

NOP

;

SACL TDXR

; !! regenerate the frame sync pulse

WAIT

;

; - - - - - - - end of main program - - - - - - - - - - ;

*Receiver Interrupt Service Routine*

TREC:

LAMM TRCV

; Load the data received from LTC1400

SFR

; Shift right two times

SFR

;

AND

#1FFFh, 0

; ANDed with #1FFFh

; For converting the data to right

; justified format

;

SACL *+, 0

; Write to data memory pointed by AR7 and

; increase the memory address by one

LACC AR7

;

SUB

#0F05h,0

; Compare to end sample address #0F05h

BCND END_TRCV, GEQ ; If the end sample address has exceeded jump

to END_TRCV

;

SPLK #040h, IMR

; Else Re-enable the TRNT receive interrupt

RETE

; Return to main program and enable interrupt

*After Obtained the Data from LTC1400, Program Jump to END_TRCV*

END_TRCV:

SPLK #002h, IMR

; Enable INT2 for program to halt

CLRC INTM

SUCCESS:

SUCCESS

*Fill the Unused Interrupt with RETE, to avoid program get “lost”*

TTRANX:

RETE

RECEIVE:

RETE

TRANSMIT:

RETE

INT2:

B halt

; Halts the running CPU

LTC1400CS8 датащи(PDF) 15 Page - Linear Technology

LTC1400CS8 датащи(HTML) 15 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

датащи скачать

ссылки URL