ML7344J datasheet(88/151 Pages) ETC2

88 / 151 page

FEDL7344C/E/J-04

ML7344C/E/J

88/151

●Low speed clock shift detection function

ML7344 has low spleed frequency shift detection function to compensate inaccurate clock generated by RC

oscillator (external clock or internal RC oscillation circuits). By detecting frequency shift of the wake up timer,

host can set wake-up timer parameters which taking frequency shift into consideration. More accurate timer

operation is possible by adjusting wake-up timer interval setting ([WUT_INTERVAL_H/L: B0 0x2F/0x30]) or

continuous operation timer interval ([WU_DURATION: B0 0x31]).

Setting

Frequency shift detection clock frequency setting

[CLK_CAL_SET: B0 0x70]

Clock calibration time

[CLK_CAL_TIME: B0 0x71]

Clock calibration result value

[CLK_CAL_H: B0 0x72], [CLK_CAL_L: B0 0x73]

This function is to measure low speed wake-up timer cycle by using accurate high speed internal clock and

count result will be stored in [CLK_CAL_H/L: B0 0x72/0x73] registers. Above setting and count numbers are

as follows:

High speed clock counter = {Wakeup timer clock cycle[SLEEP/WU_SET:B0 0x2D(2)] *

Clcok calibration time setting ([CLK_CAL_TIME:B0 0x71(5-0)]) /

{master clock cycle (26MHz) / clock division setting value ([CLK_CAL_SET:

B0 0x70(7-4)])}

Clock calibration time is as follows:

Clock calibration time[s] = Wakeup timer clock cycle * Clock calibration time setting

[Example]

Assuming no division in the internal high speed clock, calibration time is set as 10 cycle and set 1,000 to the

Wake-up interval timer value.

condition: Wakeup timer clock frequency = 32.768kHz

Detection clock division setting CLK_CAL_DIV[3:0][CLK_CAL_SET: B0 0x70(7-4)] = 0b0000

Clock calibration time setting [CLK_CAL_TIME] = 0x0A

Wake-up interval timert setting [WUT_INTERVAL_H/L:B0 0x2F,30] = 0x03E8

Theoretical high speed clock count = (1/32.768kHz) * 10 / (1/(26/1)MHz)

= 7934(0x1EFE)

If getting [CLK_CAL_H/L:B0 0x72,73] = 0x1E17 (7703)

Counter difference = 7934-7703=231

Frequency shift = (231 * 32.768^2) / (10/(1/(26000/1))-231 * 32.768 = 0.983 kHz

Then finding wake-up timer clock frequency accuracy is +3% higher. And the compensation vale (C) is

calcurared as below:

C = Wake-up timer interval([WUT_INTERVAL_H/L:B0 0x2F,30]) * frequecy shift / 32.768

= 1000 * 0.983 / 32.768 =30

Therefore, setting [WUT_INTERVAL_H/L:B0 0x2F,30] = 1000+30 =0x0406 to achive more accurate

inteval timinig.

NOTE:

If calibration time is too short or if high speed counter is divided into low speed clock, calibration may not be

accurate.

ML7344J датащи(PDF) 88 Page - List of Unclassifed Manufacturers

ML7344J датащи(HTML) 88 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL