AT25DF321A datasheet(41/53 Pages) ETC2

41 / 53 page

3686F–DFLASH–1/2014

AT25DF321A

13.

RapidS Implementation

To implement RapidS and operate at clock frequencies higher than what can be achieved in a viable SPI implementation, a full

clock cycle can be used to transmit data back and forth across the serial bus. The AT25DF321A is designed to always clock its

data out on the falling edge of the SCK signal and clock data in on the rising edge of SCK.

For full clock cycle operation to be achieved, when the AT25DF321A is clocking data out on the falling edge of SCK, the host

controller should wait until the next falling edge of SCK to latch the data in. Similarly, the host controller should clock its data

out on the rising edge of SCK in order to give the AT25DF321A a full clock cycle to latch the incoming data in on the next

rising edge of SCK.

Implementing RapidS allows a system to run at higher clock frequencies since a full clock cycle is used to accommodate a

device’s clock-to-output time, input setup time, and associated rise/fall times. For example, if the system clock frequency is

100MHz (10ns cycle time) with a 50% duty cycle, and the host controller has an input setup time of 2ns, then a standard SPI

implementation would require that the slave device be capable of outputting its data in less than 3ns to meet the 2ns host

controller setup time [(10ns x 50%) – 2ns] not accounting for rise/fall times. In an SPI mode 0 or 3 implementation, the SPI

master is designed to clock in data on the next immediate rising edge of SCK after the SPI slave has clocked its data out on the

preceding falling edge. This essentially makes SPI a half-clock cycle protocol and requires extremely fast clock-to-output

times and input setup times in order to run at high clock frequencies. With a RapidS implementation of this example, however,

the full 10ns cycle time is available which gives the slave device up to 8ns, not accounting for rise/fall times, to clock its data

out. Likewise, with RapidS, the host controller has more time available to output its data to the slave since the slave device

would be clocking that data in a full clock cycle later.

Figure 13-1.RapidS Operation

SCK

MOSI

MISO

234567

MOSI = Master Out, Slave In

MISO = Master In, Slave Out

The Master is the ASIC/MCU and the Slave is the memory device.

The Master always clocks data out on the rising edge of SCK and always clocks data in on the falling edge of SCK.

The Slave always clocks data out on the falling edge of SCK and always clocks data in on the rising edge of SCK.

Master clocks out first bit of BYTE A on the rising edge of SCK.

Slave clocks in first bit of BYTE A on the next rising edge of SCK.

Master clocks out second bit of BYTE A on the same rising edge of SCK.

Last bit of BYTE A is clocked out from the Master.

Last bit of BYTE A is clocked into the slave.

Slave clocks out first bit of BYTE B.

Master clocks in first bit of BYTE B.

Slave clocks out second bit of BYTE B.

Master clocks in last bit of BYTE B.

BYTE A

MSB

LSB

BYTE B

MSB

LSB

Slave

AT25DF321A датащи(PDF) 41 Page - List of Unclassifed Manufacturers

AT25DF321A датащи(HTML) 41 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53

датащи скачать

ссылки URL