| поискавой системы для электроныых деталей |
|
PIC16 датащи(PDF) 44 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC16 датащи(HTML) 44 Page - Microchip Technology |
|
44 / 418 page ![]() PIC16(L)F1508/9 DS40001609C-page 44 2011-2013 Microchip Technology Inc. REGISTER 4-2: CONFIG2: CONFIGURATION WORD 2 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 U-1 LVP(1) DEBUG(3) LPBOR BORV(2) STVREN — bit 13 bit 8 U-1U-1 U-1U-1 U-1U-1 R/P-1 R/P-1 — — — — — —WRT<1:0> bit 7 bit 0 Legend: R = Readable bit P = Programmable bit U = Unimplemented bit, read as ‘1’ ‘0’ = Bit is cleared ‘1’ = Bit is set -n = Value when blank or after Bulk Erase bit 13 LVP: Low-Voltage Programming Enable bit(1) 1 = Low-voltage programming enabled 0 = High-voltage on MCLR must be used for programming bit 12 DEBUG: In-Circuit Debugger Mode bit(3) 1 = In-Circuit Debugger disabled, ICSPCLK and ICSPDAT are general purpose I/O pins 0 = In-Circuit Debugger enabled, ICSPCLK and ICSPDAT are dedicated to the debugger bit 11 LPBOR: Low-Power BOR Enable bit 1 = Low-Power Brown-out Reset is disabled 0 = Low-Power Brown-out Reset is enabled bit 10 BORV: Brown-Out Reset Voltage Selection bit(2) 1 = Brown-out Reset voltage (VBOR), low trip point selected 0 = Brown-out Reset voltage (VBOR), high trip point selected bit 9 STVREN: Stack Overflow/Underflow Reset Enable bit 1 = Stack Overflow or Underflow will cause a Reset 0 = Stack Overflow or Underflow will not cause a Reset bit 8-2 Unimplemented: Read as ‘1’ bit 1-0 WRT<1:0>: Flash Memory Self-Write Protection bits 4 kW Flash memory (PIC16(L)F1508 only) 11 = Write protection off 10 = 000h to 1FFh write protected, 200h to FFFh may be modified 01 = 000h to 7FFh write protected, 800h to FFFh may be modified 00 = 000h to FFFh write protected, no addresses may be modified 8 kW Flash memory (PIC16(L)F1509 only) 11 = Write protection off 10 = 000h to 01FFh write protected, 0200h to 1FFFh may be modified 01 = 000h to 0FFFh write protected, 1000h to 1FFFh may be modified 00 = 000h to 1FFFh write protected, no addresses may be modified Note 1: The LVP bit cannot be programmed to ‘0’ when Programming mode is entered via LVP. 2: See VBOR parameter for specific trip point voltages. 3: The DEBUG bit in Configuration Words is managed automatically by device development tools including debuggers and programmers. For normal device operation, this bit should be maintained as a ‘1’. |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |