DM300018 datasheet(20/115 Pages) MICROCHIP

20 / 115 page

dsPICDEM 2 Development Board User’s Guide

DS51558A-page 14

Out-of-the-box, you can power up the dsPICDEM™ 2 Development Board and run the

sample application on the dsPIC30F4011 device. The objective of this process is to

acquaint you with the board and demonstrate how the dsPIC30F device interacts with

the hardware components used for the demo (see Section 2.4 “Out-of-the-Box

Demo”).

Eventually, as you develop your own application, you will need to program and debug

the dsPIC30F device. The second phase of the getting-started process is programming

the device for stand-alone operation. For this process, you attach the MPLAB ICD 2

In-Circuit Debugger to the dsPICDEM 2 board, designate it as a programmer in MPLAB

IDE, build your program in MPLAB IDE and then program the device with MPLAB ICD

2. The procedures for this process are outline in Section 2.5 “Device Programming

Process”, using the dsPIC30F4011 device as an example.

To examine program operation on a step-by-step basis, you need to set up MPLAB ICD

2 as a debugger. For this process you attach the MPLAB ICD 2 In-Circuit Debugger to

the dsPICDEM 2 board, designate it as a debugger in MPLAB IDE, build your program

in MPLAB IDE and then program the device for debug mode with MPLAB ICD 2. The

procedures for this process are outline in Section 2.6 “In-Circuit Debugging

Process”, using the dsPIC30F4011 device as an example.

2.4

OUT-OF-THE-BOX DEMO

As the first phase of your getting-started process, you only need to connect your PC to

the dsPICDEM™ 2 Development Board, apply power to the board and observe the

sample application on the board and on HyperTerminal®.

2.4.1

dsPICDEM 2 Configuration

Out-of-the-box, the dsPICDEM™ 2 Development Board is configured to operate with

the dsPIC304011 device. When you use a different type of supported device you need

to reconfigure the board for that device. In general, you follow this process to reconfig-

ure the dsPICDEM™ 2 Development Board. For the out-of-the-box configuration, you

simply can verify these settings:

Select a supported dsPIC30F device and plug it into the appropriate socket (not

necessary out of the box).

Note the hardware configuration for the dsPIC30F4011device:

This functionality:

Is set up by this hardware component:

Program/Debug device

Switch S2 switched OFF

Alternate Debugging

Switch S3 or S4 – all switches OFF

Temperature (A/D)

H10 set to M ALL

Potentiometer (A/D)

H13 set to M ALL

CAN

H2 open

UART1

H3 open

Alternate UART1

H4 set to M ALL

UART2

H5 open

LCD (SPI)

H1 set to M 40

SPI™ Controller ProgrammingH11 open

Switch S5 (INT0)

H6 set to M ALL

Switch S6 (INT1)

H7 set to M ALL

External connections

H8 or H9 open

LEDs D3 and D4 (I/O)

H12 set to M

Power Supply

Jumpers JP1 and JP2

Note:

Chapters 3-13 provide specific set-up instructions for each type of

dsPIC30F device supported by the dsPICDEM™ 2 Development Board.

DM300018 датащи(PDF) 20 Page - Microchip Technology

DM300018 датащи(HTML) 20 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL