DOC7707 datasheet(155/307 Pages) ETC1

155 / 307 page

155

7707F–AVR–11/10

AT90USB82/162

UDRn in order to clear UDREn or disable the Data Register Empty interrupt, otherwise a new

interrupt will occur once the interrupt routine terminates.

The Transmit Complete (TXCn) Flag bit is set one when the entire frame in the Transmit Shift

The TXCn Flag bit is automatically cleared when a transmit complete interrupt is executed, or it

can be cleared by writing a one to its bit location. The TXCn Flag is useful in half-duplex commu-

nication interfaces (like the RS-485 standard), where a transmitting application must enter

receive mode and free the communication bus immediately after completing the transmission.

When the Transmit Compete Interrupt Enable (TXCIEn) bit in UCSRnB is set, the USART

Transmit Complete Interrupt will be executed when the TXCn Flag becomes set (provided that

global interrupts are enabled). When the transmit complete interrupt is used, the interrupt han-

dling routine does not have to clear the TXCn Flag, this is done automatically when the interrupt

is executed.

17.5.4

Parity Generator

The Parity Generator calculates the parity bit for the serial frame data. When parity bit is enabled

(UPMn1 = 1), the transmitter control logic inserts the parity bit between the last data bit and the

first stop bit of the frame that is sent.

17.5.5

Disabling the Transmitter

The disabling of the Transmitter (setting the TXEN to zero) will not become effective until ongo-

ing and pending transmissions are completed, i.e., when the Transmit Shift Register and

Transmit Buffer Register do not contain data to be transmitted. When disabled, the Transmitter

will no longer override the TxDn pin.

17.6

Data Reception – The USART Receiver

The USART Receiver is enabled by writing the Receive Enable (RXENn) bit in the

UCSRnB Register to one. When the Receiver is enabled, the normal pin operation of the RxDn

pin is overridden by the USART and given the function as the Receiver’s serial input. The baud

rate, mode of operation and frame format must be set up once before any serial reception can

be done. If synchronous operation is used, the clock on the XCKn pin will be used as transfer

clock.

17.6.1

Receiving Frames with 5 to 8 Data Bits

The Receiver starts data reception when it detects a valid start bit. Each bit that follows the start

bit will be sampled at the baud rate or XCKn clock, and shifted into the Receive Shift Register

until the first stop bit of a frame is received. A second stop bit will be ignored by the Receiver.

When the first stop bit is received, i.e., a complete serial frame is present in the Receive Shift

buffer can then be read by reading the UDRn I/O location.

The following code example shows a simple USART receive function based on polling of the

Receive Complete (RXCn) Flag. When using frames with less than eight bits the most significant

DOC7707 датащи(PDF) 155 Page - List of Unclassifed Manufacturers

DOC7707 датащи(HTML) 155 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL