DOC7707 datasheet(35/307 Pages) ETC1

35 / 307 page

7707F–AVR–11/10

AT90USB82/162

the system clock frequency and the power consumption when the requirement for processing

power is low. This can be used with all clock source options, and it will affect the clock frequency

of the CPU and all synchronous peripherals. clk

I/O, clkCPU, and clkFLASH are divided by a factor as

shown in Table 6-9.

When switching between prescaler settings, the System Clock Prescaler ensures that no

glitches occurs in the clock system. It also ensures that no intermediate frequency is higher than

neither the clock frequency corresponding to the previous setting, nor the clock frequency corre-

sponding to the new setting.

The ripple counter that implements the prescaler runs at the frequency of the undivided clock,

which may be faster than the CPU's clock frequency. Hence, it is not possible to determine the

state of the prescaler - even if it were readable, and the exact time it takes to switch from one

clock division to the other cannot be exactly predicted. From the time the CLKPS values are writ-

ten, it takes between T1 + T2 and T1 + 2 * T2 before the new clock frequency is active. In this

interval, 2 active clock edges are produced. Here, T1 is the previous clock period, and T2 is the

period corresponding to the new prescaler setting.

To avoid unintentional changes of clock frequency, a special write procedure must be followed

to change the CLKPS bits:

Write the Clock Prescaler Change Enable (CLKPCE) bit to one and all other bits in

CLKPR to zero.

Within four cycles, write the desired value to CLKPS while writing a zero to CLKPCE.

Interrupts must be disabled when changing prescaler setting to make sure the write procedure is

not interrupted.

6.8.1

Clock Prescale Register – CLKPR

• Bit 7 – CLKPCE: Clock Prescaler Change Enable

The CLKPCE bit must be written to logic one to enable change of the CLKPS bits. The CLKPCE

bit is only updated when the other bits in CLKPR are simultaneously written to zero. CLKPCE is

cleared by hardware four cycles after it is written or when CLKPS bits are written. Rewriting the

CLKPCE bit within this time-out period does neither extend the time-out period, nor clear the

CLKPCE bit.

• Bit 6-4 - Reserved bits

These bits are reserved and will always read as zero.

• Bits 3..0 – CLKPS3..0: Clock Prescaler Select Bits 3 - 0

These bits define the division factor between the selected clock source and the internal system

clock. These bits can be written run-time to vary the clock frequency to suit the application

requirements. As the divider divides the master clock input to the MCU, the speed of all synchro-

nous peripherals is reduced when a division factor is used. The division factors are given in

Table 6-9.

The CKDIV8 Fuse determines the initial value of the CLKPS bits. If CKDIV8 is unprogrammed,

the CLKPS bits will be reset to “0000”. If CKDIV8 is programmed, CLKPS bits are reset to

Bit

543

CLKPCE

–

CLKPS3

CLKPS2

CLKPS1

CLKPS0

CLKPR

Read/Write

R/W

Initial Value

See Bit Description

DOC7707 датащи(PDF) 35 Page - List of Unclassifed Manufacturers

DOC7707 датащи(HTML) 35 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL