DOC7707 datasheet(153/307 Pages) ETC1

153 / 307 page

153

7707F–AVR–11/10

AT90USB82/162

17.5

Data Transmission – The USART Transmitter

The USART Transmitter is enabled by setting the Transmit Enable (TXEN) bit in the UCSRnB

den by the USART and given the function as the Transmitter’s serial output. The baud rate,

mode of operation and frame format must be set up once before doing any transmissions. If syn-

chronous operation is used, the clock on the XCKn pin will be overridden and used as

transmission clock.

17.5.1

Sending Frames with 5 to 8 Data Bit

A data transmission is initiated by loading the transmit buffer with the data to be transmitted. The

CPU can load the transmit buffer by writing to the UDRn I/O location. The buffered data in the

transmit buffer will be moved to the Shift Register when the Shift Register is ready to send a new

frame. The Shift Register is loaded with new data if it is in idle state (no ongoing transmission) or

immediately after the last stop bit of the previous frame is transmitted. When the Shift Register is

loaded with new data, it will transfer one complete frame at the rate given by the Baud Register,

U2Xn bit or by XCKn depending on mode of operation.

The following code examples show a simple USART transmit function based on polling of the

Data Register Empty (UDREn) Flag. When using frames with less than eight bits, the most sig-

nificant bits written to the UDRn are ignored. The USART has to be initialized before the function

can be used. For the assembly code, the data to be sent is assumed to be stored in Register

R16

Note:

1. See “About Code Examples” on page 7.

The function simply waits for the transmit buffer to be empty by checking the UDREn Flag,

before loading it with new data to be transmitted. If the Data Register Empty interrupt is utilized,

the interrupt routine writes the data into the buffer.

17.5.2

Sending Frames with 9 Data Bit

If 9-bit characters are used (UCSZn = 7), the ninth bit must be written to the TXB8 bit in

UCSRnB before the low byte of the character is written to UDRn. The following code examples

Assembly Code Example

(1)

USART_Transmit:

; Wait for empty transmit buffer

sbis

UCSRnA,UDREn

rjmp

USART_Transmit

; Put data (r16) into buffer, sends the data

out

UDRn,r16

ret

C Code Example

(1)

void

USART_Transmit( unsigned char data )

{

/* Wait for empty transmit buffer */

while

( !( UCSRnA & (1<<UDREn)) )

;

/* Put data into buffer, sends the data */

UDRn = data;

}

DOC7707 датащи(PDF) 153 Page - List of Unclassifed Manufacturers

DOC7707 датащи(HTML) 153 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL