STM32F101RBH6 datasheet(86/90 Pages) STMICROELECTRONICS

86 / 90 page

Revision history

STM32F101x8, STM32F101xB

86/90

DocID13586 Rev 16

14-Mar-2008

Figure 2: Clock tree on page 13 added.

CRC added (see CRC (cyclic redundancy check) calculation unit on

page 9 and Figure 8: Memory map on page 29 for address).

Maximum TJ value given in Table 7: Thermal characteristics on page 33.

PD, TA and TJ added, tprog values modified and tprog description clarified in

Table 27: Flash memory characteristics on page 51.

IDD modified in Table 15: Typical and maximum current consumptions in

Stop and Standby modes on page 39.

ACCHSI modified in Table 23: HSI oscillator characteristics on page 49,

note 2 removed.

tRET modified in Table 28: Flash memory endurance and data retention.

VNF(NRST) unit corrected in Table 37: NRST pin characteristics on

page 60.

Table 41: SPI characteristics on page 65 modified.

IVREF added in Table 42: ADC characteristics on page 68.

Table 44: ADC accuracy - limited test conditions added. Table 45: ADC

accuracy modified.

LQFP100 package specifications updated (see Section 6: Package

characteristics on page 73).

Recommended LQFP100, LQFP64, LQFP48 and VFQFPN36 footprints

added (see Figure 42, Figure 44, Figure 46 and Figure 40).

Section 6.2: Thermal characteristics on page 80 modified.

Appendix A: Important notes removed.

21-Mar-2008

Small text changes.

In Table 28: Flash memory endurance and data retention:

–NEND tested over the whole temperature range

– cycling conditions specified for tRET

–tRET min modified at TA = 55 °C

Figure 2: Clock tree corrected. Figure 8: Memory map clarified.

V25, Avg_Slope and TL modified in Table 46: TS characteristics.

CRC feature removed.

22-May-2008

Section 1: Introduction modified, Section 2.2: Full compatibility throughout

the family added. CRC feature added.

IDD_VBAT removed from Table 21: Typical current consumption in Standby

mode on page 42.

Values added to Table 40: SCL frequency (fPCLK1= 36 MHz, VDD_I2C =

3.3 V) on page 64.

Figure 30: SPI timing diagram - slave mode and CPHA = 0 on page 66

modified. Equation 1 corrected.

Section 6.2.2: Evaluating the maximum junction temperature for an

application on page 81 added.

Axx option added to Table 53: Ordering information scheme on page 82.

Table 54. Document revision history (continued)

Date

Revision

Changes

STM32F101RBH6 датащи(PDF) 86 Page - STMicroelectronics

STM32F101RBH6 датащи(HTML) 86 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90

датащи скачать

ссылки URL