 |
поискавой системы для электроныых деталей |
|
|
поискавой системы для электроныых деталей |
|
HT83050 датащи(PDF) 13 Page - Holtek Semiconductor Inc |
|
|
|||||||||||||||||||||||||||||
HT83050 датащи(HTML) 13 Page - Holtek Semiconductor Inc |
|
|
13 / 40 page  HT83XXX Rev. 1.60 13 November 19, 2008 Bit No. Label Function 0 C C is set if an operation results in a carry during an addition operation or if a borrow does not take place during a subtraction operation; otherwise C is cleared. C is also affected by a ro- tate through carry instruction. 1 AC AC is set if an operation results in a carry out of the low nibbles in addition or no borrow from the high nibble into the low nibble in subtraction; otherwise AC is cleared. 2 Z Z is set if the result of an arithmetic or logical operation is zero; otherwise Z is cleared. 3 OV OV is set if an operation results in a carry into the highest-order bit but not a carry out of the highest-order bit, or vice versa; otherwise OV is cleared. 4 PDF PDF is cleared by system power-up or executing the ²CLR WDT² instruction. PDF is set by executing the ²HALT² instruction. 5 TO TO is cleared by system power-up or executing the ²CLR WDT² or ²HALT² instruction. TO is set by a WDT time-out. 6~7 ¾ Unused bit, read as ²0² Status (0AH) Register The Internal Timer Counter 0 Interrupt is initialized by setting the Timer Counter 0 interrupt request flag (T0F:bit 5 of INTC), caused by a Timer Counter 0 overflow. When the interrupt is enabled, and the stack is not full and the T0F bit is set, a subroutine call to location 08H will occur. The related interrupt request flag (T0F) will be reset and the EMI bit cleared to disable further interrupts. The Internal Timer Counter 1 Interrupt is initialized by setting the Timer Counter 1 interrupt request flag (T1F:bit 6 of INTC), caused by a Timer Counter 1 overflow. When the interrupt is enabled, and the stack is not full and the T1F bit is set, a subroutine call to location 0CH will occur. The related interrupt request flag (T1F) will be reset and the EMI bit cleared to disable further interrupts. Time Base Interrupt is triggered by set INTC.1 (ETBI) which sets the related interrupt request flag (TBF:bit 4 of INTC). When the interrupt is enabled, and the stack is not full and the external interrupt is active, a subroutine call to location 04H will occur. The interrupt request flag (TBF) and EMI bits will be cleared to disable other interrupts. During the execution of an interrupt subroutine, other in- terrupt acknowledgment are held until the ²RETI² in- struction is executed or the EMI bit and the related interrupt control bit are set to ²1² (of course, if the stack is not full). To return from the interrupt subroutine, the ²RET² or ²RETI² instruction may be invoked. RETI will set the EMI bit to enable an interrupt service, but RET will not. Interrupts occurring in the interval between the rising edges of two consecutive T2 pulses, will be serviced on the latter of the two T2 pulses, if the corresponding inter- rupts are enabled. In the case of simultaneous requests, the following table shows the priority that is applied. These can be masked by resetting the EMI bit. The Timer Counter 0/1 interrupt request flag (T0F/T1F) which enables Timer Counter 0/1 control bit (ET0I/ ET1I), the time base interrupt request flag (TBF) which enables time base control bit (ETBI) from the interrupt control reg- ister (INTC:0BH) EMI, ETBI, ET0I, ET1I are used to con- trol the enabling/disabling of interrupts. These bits prevent the requested interrupt begin serviced. Once the interrupt request flags (T0F, T1F, TBF) are set, they will remain in the INTC register until the interrupts are ser- viced or cleared by a software instruction. It is recommended that application programs do not use CALL subroutines within an interrupt subroutine. Inter- rupts often occur in an unpredictable manner or need to be serviced immediately in some applications. If only one stack is left and the interrupt enable is not well con- trolled, once a CALL subroutine if used in the interrupt subroutine will corrupt the original control sequence. Bit No. Label Function 0 EMI Controls the master (global) interrupt (1= enabled; 0= disabled) 1 ETBI Controls the time base interrupt (1= enabled; 0= disabled) 2 ET0I Controls the timer 0 interrupt (1= enabled; 0= disabled) 3 ET1I Controls the timer 1 interrupt (1= enabled; 0= disabled) 4 TBF Time base interrupt request flag (1= active; 0= inactive) 5 T0F Timer 0 request flag (1= active; 0= inactive) 6 T1F Timer 1 request flag (1= active; 0= inactive) 7 ¾ Unused bit, read as ²0² INTC (0BH) Register |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Russian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
