HT45F23 datasheet(95/152 Pages) HOLTEK

95 / 152 page

Peripheral Clock Output

The Peripheral Clock Output allows the device to supply external hardware with a clock signal

synchronised to the microcontroller clock.

Peripheral Clock Operation

As the peripheral clock output pin, PCK, is shared with I/O line, the required pin function is chosen via

PCKEN in the SIMC0 register. The Peripheral Clock function is controlled using the SIMC0 register.

The clock source for the Peripheral Clock Output can originate from either the Timer 0 output/2 or a

divided ratio of the internal fSYS clock. The PCKEN bit in the SIMC0 register is the overall on/off

control, setting PCKEN bit to

²1² enables the Peripheral Clock, setting PCKEN bit to ²0² disables it.

The required division ratio of the system clock is selected using the PCKP1 and PCKP0 bits in the

same register. If the device enters the SLEEP Mode this will disable the Peripheral Clock output.

SIMC0 Register

Bit

76543210

Name

SIM2

SIM1

SIM0

PCKEN

PCKP1

PCKP0

SIMEN

R/W

POR

1110000

Bit 7~5

SIM2, SIM1, SIM0: SIM operating mode control

000: SPI master mode; SPI clock is fSYS/4

001: SPI master mode; SPI clock is fSYS/16

010: SPI master mode; SPI clock is fSYS/64

011: SPI master mode; SPI clock is fSUB

100: SPI master mode; SPI clock is Timer 0 output/2 (PFD0)

101: SPI slave mode

110: I

2C slave mode

111: Unused mode

These bits setup the overall operating mode of the SIM function. As well as selecting if the I

or SPI function, they are used to control the SPI Master/Slave selection and the SPI Master clock

frequency. The SPI clock is a function of the system clock but can also be chosen to be sourced

from the Timer 0. If the SPI Slave Mode is selected then the clock will be supplied by an external

Master device.

Bit 4

PCKEN: PCK output pin control

0: Disable

1: Enable

Bit 3~2

PCKP1, PCKP0: select PCK output pin frequency

00: fSYS

01: fSYS/4

10: fSYS/8

11: Timer 0 output/2 (PFD0)

Bit 1

SIMEN: SIM control

0: Disable

1: Enable

The bit is the overall on/off control for the SIM interface. When the SIMEN bit is cleared to zero

to disable the SIM interface, the SDI, SDO, SCK and SCS, or SDA and SCL lines will be in a

floating condition and the SIM operating current will be reduced to a minimum value. When the bit

is high the SIM interface is enabled. The SIM configuration option must have first enabled the

SIM interface for this bit to be effective. Note that when the SIMEN bit changes from low to high

the contents of the SPI control registers will be in an unknown condition and should therefore be

first initialised by the application program.

Bit 0

unimplemented, read as

²0²

HT45F23/HT45F43

8-Bit Flash MCU with Op Amps & Comparators

Rev. 1.20

September 15, 2011

HT45F23 датащи(PDF) 95 Page - Holtek Semiconductor Inc

HT45F23 датащи(HTML) 95 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL