HT45F23 datasheet(89/152 Pages) HOLTEK

89 / 152 page

Bit

76543210

SIMC0

SIM2

SIM1

SIM0

PCKEN

PCKP1

PCKP0

SIMEN

SIMC1

HCF

HAAS

HBB

HTX

TXAK

SRW

IAMWU

RXAK

SIMD

SIMA

IICA6

IICA5

IICA4

IICA3

IICA2

IICA1

IICA0

2C Registers List

SIMC0 Register

Bit

76543210

Name

SIM2

SIM1

SIM0

PCKEN

PCKP1

PCKP0

SIMEN

R/W

POR

1110000

Bit 7~5

SIM2, SIM1, SIM0: Operating Mode Control

000: SPI master mode; SPI clock is fSYS/4

001: SPI master mode; SPI clock is fSYS/16

010: SPI master mode; SPI clock is fSYS/64

011: SPI master mode; SPI clock is fSUB

100: SPI master mode; SPI clock is Timer 0 output/2 (PFD0)

101: SPI slave mode

110: I

2C slave mode

111: Unused mode

These bits setup the overall operating mode of the SIM function. As well as selecting if the I

or SPI function, they are used to control the SPI Master/Slave selection and the SPI Master clock

frequency. The SPI clock is a function of the system clock but can also be chosen to be sourced

from the Timer 0. If the SPI Slave Mode is selected then the clock will be supplied by an external

Master device.

Bit 4

PCKEN: PCK Output Pin Control

0: Disable

1: Enable

Bit 3~2

PCKP1, PCKP0: Select PCK output pin frequency

00: fSYS

01: fSYS/4

10: fSYS/8

11: Timer 0 output/2 (PFD0)

Bit 1

SIMEN: SIM Control

0: Disable

1: Enable

The bit is the overall on/off control for the SIM interface. When the SIMEN bit is cleared to zero

to disable the SIM interface, the SDI, SDO, SCK and SCS, or SDA and SCL lines will be in a

floating condition and the SIM operating current will be reduced to a minimum value. When the bit

is high the SIM interface is enabled. The SIM configuration option must have first enabled the

SIM interface for this bit to be effective. If the SIM is configured to operate as an SPI interface via

SIM2~SIM0 bits, the contents of the SPI control registers will remain at the previous settings

when the SIMEN bit changes from low to high and should therefore be first initialised by the

application program. If the SIM is configured to operate as an I

2C interface via the SIM2~SIM0

bits and the SIMEN bit changes from low to high, the contents of the I

2C control bits such as HTX

and TXAK will remain at the previous settings and should therefore be first initialised by the

application program while the relevant I

2C flags such as HCF, HAAS, HBB, SRW and RXAK will

be set to their default states.

Bit 0

unimplemented, read as

²0²

HT45F23/HT45F43

8-Bit Flash MCU with Op Amps & Comparators

Rev. 1.20

September 15, 2011

HT45F23 датащи(PDF) 89 Page - Holtek Semiconductor Inc

HT45F23 датащи(HTML) 89 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL