PIC12F1822-ISLASHMF datasheet(257/398 Pages) MICROCHIP

257 / 398 page

 2010 Microchip Technology Inc.

Preliminary

DS41413A-page 257

PIC12F/LF1822/16F/LF1823

24.6

I2C MASTER MODE

Master mode is enabled by setting and clearing the

appropriate SSP1M bits in the SSP1CON1 register and

by setting the SSP1EN bit. In Master mode, the SCL

and SDA lines are set as inputs and are manipulated by

the MSSP1 hardware.

Master mode of operation is supported by interrupt

generation on the detection of the Start and Stop con-

ditions. The Stop (P) and Start (S) bits are cleared from

a Reset or when the MSSP1 module is disabled. Con-

trol of the I2C bus may be taken when the P bit is set,

or the bus is Idle.

In Firmware Controlled Master mode, user code

conducts all I2C bus operations based on Start and

Stop bit condition detection. Start and Stop condition

detection is the only active circuitry in this mode. All

other communication is done by the user software

directly manipulating the SDA and SCL lines.

The following events will cause the SSP1 Interrupt Flag

bit, SSP1IF, to be set (SSP1 interrupt, if enabled):

• Start condition detected

• Stop condition detected

• Data transfer byte transmitted/received

• Acknowledge transmitted/received

• Repeated Start generated

24.6.1

I2C MASTER MODE OPERATION

The master device generates all of the serial clock

pulses and the Start and Stop conditions. A transfer is

ended with a Stop condition or with a Repeated Start

condition. Since the Repeated Start condition is also

the beginning of the next serial transfer, the I2C bus will

not be released.

In Master Transmitter mode, serial data is output

through SDA, while SCL outputs the serial clock. The

first byte transmitted contains the slave address of the

receiving device (7 bits) and the Read/Write (R/W) bit.

In this case, the R/W bit will be logic ‘0’. Serial data is

transmitted 8 bits at a time. After each byte is transmit-

ted, an Acknowledge bit is received. Start and Stop

conditions are output to indicate the beginning and the

end of a serial transfer.

In Master Receive mode, the first byte transmitted con-

tains the slave address of the transmitting device

(7 bits) and the R/W bit. In this case, the R/W bit will be

logic ‘1’. Thus, the first byte transmitted is a 7-bit slave

address followed by a ‘1’ to indicate the receive bit.

Serial data is received via SDA, while SCL outputs the

serial clock. Serial data is received 8 bits at a time. After

each byte is received, an Acknowledge bit is transmit-

ted. Start and Stop conditions indicate the beginning

and end of transmission.

A Baud Rate Generator is used to set the clock

frequency output on SCL. See Section 24.7 “Baud

Rate Generator” for more detail.

Note 1: The MSSP1 module, when configured in

I2C Master mode, does not allow queue-

ing of events. For instance, the user is not

allowed to initiate a Start condition and

immediately write the SSP1BUF register

to initiate transmission before the Start

condition is complete. In this case, the

SSP1BUF will not be written to and the

WCOL bit will be set, indicating that a write

to the SSP1BUF did not occur

2: When in Master mode, Start/Stop detec-

tion is masked and an interrupt is gener-

ated when the SEN/PEN bit is cleared and

the generation is complete.

PIC12F1822-I/MF датащи(PDF) 257 Page - Microchip Technology

PIC12F1822-I/MF датащи(HTML) 257 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL