ATmega328P datasheet(285/448 Pages) ATMEL

285 / 448 page

285

8161D–AVR–10/09

ATmega48PA/88PA/168PA/328P

instruction is executed within three CPU cycles after the BLBSET and SELFPRGEN bits are set

in SPMCSR, the value of the Lock bits will be loaded in the destination register. The BLBSET

and SELFPRGEN bits will auto-clear upon completion of reading the Lock bits or if no LPM

instruction is executed within three CPU cycles or no SPM instruction is executed within four

CPU cycles. When BLBSET and SELFPRGEN are cleared, LPM will work as described in the

Instruction set Manual.

The algorithm for reading the Fuse Low byte is similar to the one described above for reading

the Lock bits. To read the Fuse Low byte, load the Z-pointer with 0x0000 and set the BLBSET

and SELFPRGEN bits in SPMCSR. When an LPM instruction is executed within three cycles

after the BLBSET and SELFPRGEN bits are set in the SPMCSR, the value of the Fuse Low byte

(FLB) will be loaded in the destination register as shown below. Refer to Table 27-5 on page 296

for a detailed description and mapping of the Fuse Low byte.

Similarly, when reading the Fuse High byte, load 0x0003 in the Z-pointer. When an LPM instruc-

tion is executed within three cycles after the BLBSET and SELFPRGEN bits are set in the

SPMCSR, the value of the Fuse High byte (FHB) will be loaded in the destination register as

shown below. Refer to Table 27-7 on page 296 for detailed description and mapping of the Fuse

High byte.

When reading the Extended Fuse byte, load 0x0002 in the Z-pointer. When an LPM instruction

is executed within three cycles after the BLBSET and SELFPRGEN bits are set in the SPMCSR,

the value of the Extended Fuse byte (EFB) will be loaded in the destination register as shown

below. Refer to Table 27-5 on page 296 for detailed description and mapping of the Extended

Fuse byte.

Fuse and Lock bits that are programmed, will be read as zero. Fuse and Lock bits that are

unprogrammed, will be read as one.

26.8.10

Reading the Signature Row from Software

To read the Signature Row from software, load the Z-pointer with the signature byte address

given in Table 26-5 on page 286 and set the SIGRD and SPMEN bits in SPMCSR. When an

LPM instruction is executed within three CPU cycles after the SIGRD and SPMEN bits are set in

SPMCSR, the signature byte value will be loaded in the destination register. The SIGRD and

SPMEN bits will auto-clear upon completion of reading the Signature Row Lock bits or if no LPM

instruction is executed within three CPU cycles. When SIGRD and SPMEN are cleared, LPM will

work as described in the Instruction set Manual.

Bit

76543210

–

BLB12

BLB11

BLB02

BLB01

LB2

LB1

Bit

321

FLB7

FLB6

FLB5

FLB4

FLB3

FLB2

FLB1

FLB0

Bit

321

FHB7

FHB6

FHB5

FHB4

FHB3

FHB2

FHB1

FHB0

Bit

321

–

EFB3

EFB2

EFB1

EFB0

ATmega328P датащи(PDF) 285 Page - ATMEL Corporation

ATmega328P датащи(HTML) 285 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL