ATmega328P datasheet(228/448 Pages) ATMEL

228 / 448 page

228

8161D–AVR–10/09

ATmega48PA/88PA/168PA/328P

Figure 21-11. Data Transfer in Master Transmitter Mode

A START condition is sent by writing the following value to TWCR:

TWEN must be set to enable the 2-wire Serial Interface, TWSTA must be written to one to trans-

mit a START condition and TWINT must be written to one to clear the TWINT Flag. The TWI will

then test the 2-wire Serial Bus and generate a START condition as soon as the bus becomes

free. After a START condition has been transmitted, the TWINT Flag is set by hardware, and the

status code in TWSR will be 0x08 (see Table 21-2). In order to enter MT mode, SLA+W must be

transmitted. This is done by writing SLA+W to TWDR. Thereafter the TWINT bit should be

cleared (by writing it to one) to continue the transfer. This is accomplished by writing the follow-

ing value to TWCR:

When SLA+W have been transmitted and an acknowledgement bit has been received, TWINT is

set again and a number of status codes in TWSR are possible. Possible status codes in Master

mode are 0x18, 0x20, or 0x38. The appropriate action to be taken for each of these status codes

is detailed in Table 21-2.

When SLA+W has been successfully transmitted, a data packet should be transmitted. This is

done by writing the data byte to TWDR. TWDR must only be written when TWINT is high. If not,

the access will be discarded, and the Write Collision bit (TWWC) will be set in the TWCR Regis-

ter. After updating TWDR, the TWINT bit should be cleared (by writing it to one) to continue the

transfer. This is accomplished by writing the following value to TWCR:

This scheme is repeated until the last byte has been sent and the transfer is ended by generat-

ing a STOP condition or a repeated START condition. A STOP condition is generated by writing

the following value to TWCR:

A REPEATED START condition is generated by writing the following value to TWCR:

TWCR

TWINT

TWEA

TWSTA

TWSTO

TWWC

TWEN

–

TWIE

value

TWCR

TWINT

TWEA

TWSTA

TWSTO

TWWC

TWEN

–

TWIE

value

TWCR

TWINT

TWEA

TWSTA

TWSTO

TWWC

TWEN

–

TWIE

value

TWCR

TWINT

TWEA

TWSTA

TWSTO

TWWC

TWEN

–

TWIE

value

TWCR

TWINT

TWEA

TWSTA

TWSTO

TWWC

TWEN

–

TWIE

value

Device 1

MASTER

TRANSMITTER

Device 2

SLAVE

RECEIVER

Device 3

Device n

SDA

SCL

........

ATmega328P датащи(PDF) 228 Page - ATMEL Corporation

ATmega328P датащи(HTML) 228 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL