| поискавой системы для электроныых деталей |
|
ATmega325P датащи(PDF) 298 Page - ATMEL Corporation |
|
|
|||||||||||||||||||||||||||||
ATmega325P датащи(HTML) 298 Page - ATMEL Corporation |
|
298 / 364 page ![]() 298 8023F–AVR–07/09 ATmega325P/3250P Notes: 1. This command sequence is not required if the seven MSB are correctly set by the previous command sequence (which is normally the case). 2. Repeat until o = “1”. 3. Set bits to “0” to program the corresponding Fuse, “1” to unprogram the Fuse. 4. Set bits to “0” to program the corresponding Lock bit, “1” to leave the Lock bit unchanged. 5. “0” = programmed, “1” = unprogrammed. 6. The bit mapping for Fuses Extended byte is listed in Table 25-3 on page 272 7. The bit mapping for Fuses High byte is listed in Table 25-4 on page 273 8. The bit mapping for Fuses Low byte is listed in Table 25-5 on page 273 9. The bit mapping for Lock bits byte is listed in Table 25-1 on page 271 10. Address bits exceeding PCMSB and EEAMSB (Table 25-11 and Table 25-12) are don’t care 11. All TDI and TDO sequences are represented by binary digits (0b...). 8f. Read Fuses and Lock Bits 0111010_00000000 0111110_00000000 0110010_00000000 0110110_00000000 0110111_00000000 xxxxxxx_xxxxxxxx xxxxxxx_oooooooo xxxxxxx_oooooooo xxxxxxx_oooooooo xxxxxxx_oooooooo (5) Fuse Ext. byte Fuse High byte Fuse Low byte Lock bits 9a. Enter Signature Byte Read 0100011_00001000 xxxxxxx_xxxxxxxx 9b. Load Address Byte 0000011_bbbbbbbb xxxxxxx_xxxxxxxx 9c. Read Signature Byte 0110010_00000000 0110011_00000000 xxxxxxx_xxxxxxxx xxxxxxx_oooooooo 10a. Enter Calibration Byte Read 0100011_00001000 xxxxxxx_xxxxxxxx 10b. Load Address Byte 0000011_bbbbbbbb xxxxxxx_xxxxxxxx 10c. Read Calibration Byte 0110110_00000000 0110111_00000000 xxxxxxx_xxxxxxxx xxxxxxx_oooooooo 11a. Load No Operation Command 0100011_00000000 0110011_00000000 xxxxxxx_xxxxxxxx xxxxxxx_xxxxxxxx Table 25-17. JTAG Programming Instruction Set (Continued) a = address high bits, b = address low bits, H = 0 - Low byte, 1 - High Byte, o = data out, i = data in, x = don’t care Instruction TDI Sequence TDO Sequence Notes |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |