ATmega169P datasheet(144/393 Pages) ATMEL

144 / 393 page

144

8018N–AVR–08/09

ATmega169P

Figure 17-5. CTC Mode, Timing Diagram

An interrupt can be generated each time the counter value reaches the TOP value by using the

OCF2A Flag. If the interrupt is enabled, the interrupt handler routine can be used for updating

the TOP value. However, changing the TOP to a value close to BOTTOM when the counter is

running with none or a low prescaler value must be done with care since the CTC mode does

not have the double buffering feature. If the new value written to OCR2A is lower than the cur-

rent value of TCNT2, the counter will miss the compare match. The counter will then have to

count to its maximum value (0xFF) and wrap around starting at 0x00 before the compare match

can occur.

For generating a waveform output in CTC mode, the OC2A output can be set to toggle its logical

level on each compare match by setting the Compare Output mode bits to toggle mode

(COM2A1:0 = 1). The OC2A value will not be visible on the port pin unless the data direction for

the pin is set to output. The waveform generated will have a maximum frequency of f

OC2A =

clk_I/O/2 when OCR2A is set to zero (0x00). The waveform frequency is defined by the following

equation:

The N variable represents the prescale factor (1, 8, 32, 64, 128, 256, or 1024).

As for the Normal mode of operation, the TOV2 Flag is set in the same timer clock cycle that the

counter counts from MAX to 0x00.

17.6.3

Fast PWM Mode

The fast Pulse Width Modulation or fast PWM mode (WGM21:0 = 3) provides a high frequency

PWM waveform generation option. The fast PWM differs from the other PWM option by its sin-

gle-slope operation. The counter counts from BOTTOM to MAX then restarts from BOTTOM. In

non-inverting Compare Output mode, the Output Compare (OC2A) is cleared on the compare

match between TCNT2 and OCR2A, and set at BOTTOM. In inverting Compare Output mode,

the output is set on compare match and cleared at BOTTOM. Due to the single-slope operation,

the operating frequency of the fast PWM mode can be twice as high as the phase correct PWM

mode that uses dual-slope operation. This high frequency makes the fast PWM mode well suited

for power regulation, rectification, and DAC applications. High frequency allows physically small

sized external components (coils, capacitors), and therefore reduces total system cost.

In fast PWM mode, the counter is incremented until the counter value matches the MAX value.

The counter is then cleared at the following timer clock cycle. The timing diagram for the fast

TCNTn

OCnx

(Toggle)

OCnx Interrupt Flag Set

Period

(COMnx1:0 = 1)

fOCnx

clk_I/O

OCRnx

()

⋅⋅

--------------------------------------------------

ATmega169P датащи(PDF) 144 Page - ATMEL Corporation

ATmega169P датащи(HTML) 144 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL