9

 2003 Semtech Corp.

www.semtech.com

POWER MANAGEMENT

SC1211

Inductor C urrent Signal

Vout

Qcst

VIN

Rcs

C

SC1211

PGND

VIN

VPN

Lo

Q2

Qcsb

DRN

Q1

+

Co

Ccs

technique. An internal totem pole (Qcst, Qcsb) generates

a VPN (Virtual Phase Node) signal. This VPN follows the

DRN (or the Power Phase Node) with the same timing. A

RC network (Rcs and Ccs) is connected between VPN

and Vout. During Q1 turn-on, Qcst turns on as well. The

voltage drop across Q1 and Lo charges Ccs. During Q2

turn-on, Qcsb turns on as well. The voltage drop across

Q2 and Lo discharges Ccs. Both voltage drops are pro-

portional to the inductor current and a resistance equal

to FET’s Rdson plus ESR of the inductor. If the time con-

stant Rcs x Ccs is close to the Lo/Ro of the inductor,

where Ro is given by

)

1

(

*

*

_

_

D

R

D

R

R

Ro

ls

dson

hs

dson

inductor

-

+

+

=

the signal developed across Ccs will be proportional to

the inductor current, where Ro is the equivalent current

sensing resistance. In the above equation, Rinductor is

ESR of the inductor, Rdson_hs and Rdson_ls are the top

and bottom FET’s Rdson, and D is the duty cycle of the

converter.

Since a perfect timing match down to the nanosecond is

impossible, the VPN totem pole is held in tri-state during

the communtations of DRN in the SC1211. This avoids

errors and offset on the current detection which can be

significant since the timing mismatch is multiplied by the

input voltage. An optional capacitor between VPN and

DRN allows these two nodes to be AC coupled during

the tri-state window, hence yields a perfect timing match.

Applications Information (Cont.)

Mode Controller about the details of the Combi-Sense

technique.

Optimized Gat

Optimized Gat

Optimized Gat

Optimized Gat

Optimized Gate Driv

e Driv

e Driv

e Driv

e Drive V

e V

e V

e V

e Voltage

oltage

oltage

oltage

oltage

With the supply voltage in between 9V to 16V, an inter-

nal LDO is designed with the SC1211 to bring the volt-

age to a lower level for gate drive. An external Ceramic

capacitor(1uF to 4.7uF) connected in between Vreg to

ground is needed to support the LDO. The LDO output is

connected to low gate drive internally, and has to be

connected to high gate drive through an external boot-

strap circuit. The LDO output voltage is set at 8.5V. The

manufacture data and bench tested results show that,

mum gate drive voltage is around 8.5V, where the total

power losses of power FETs, including conduction loss

and switching loss, are minimized.

Thermal Shut Down

Thermal Shut Down

Thermal Shut Down

Thermal Shut Down

Thermal Shut Down

The SC1211 will shut down by pulling both driver out-

COMPONENT SELECTION

COMPONENT SELECTION

COMPONENT SELECTION

COMPONENT SELECTION

COMPONENT SELECTION

Switching F

Switching F

Switching F

Switching F

Switching Freq

req

req

req

requency

uency

uency

uency

uency, Induct

, Induct

, Induct

, Induct

, Inductor and MOSFET

or and MOSFET

or and MOSFET

or and MOSFET

or and MOSFETsssss

The SC1211 is capable of providing up to 3.5A peak

drive current, and operating up to 1.5MHz PWM frequency

without causing thermal stress on the driver. The selec-

tion of switching frequency, together with inductor and

FETs is a trade-off between the cost, size, and thermal

management of a multi-phase voltage regulator. In mod-

ern microprocessor applications, these parameters could

be in the range of:

Switching Frequency 100kHz to 500kHz per phase

Inductor Value

0.2uH to 2uH

FETs

20nC to 100nC total gate charge

Bootstrap Circuit

Bootstrap Circuit

Bootstrap Circuit

Bootstrap Circuit

Bootstrap Circuit

The SC1211 uses an external bootstrap circuit to pro-

vide a voltage for the top FET drive. This voltage, refer-

ring to the Phase Node, is held up by a bootstrap capaci-