AD5752 datasheet(20/32 Pages) AD

20 / 32 page

AD5722/AD5732/AD5752

Rev. 0 | Page 20 of 32

LOAD DAC (LDAC

After data has been transferred into the input register of the

DACs, there are two ways to update the DAC registers and DAC

outputs. Depending on the status of both

)

SYNC and

SYNC

SCLK

VOUTX

DAC

INTERFACE

LOGIC

OUTPUT

AMPLIFIER

LDAC

SDO

SDIN

REFIN

INPUT

12-/14-/16-BIT

DAC

LDAC, one

of two update modes is selected: individual DAC updating or

simultaneous updating of all DACs.

Figure 41. Simplified Diagram of Input Loading Circuitry for One DAC

Individual DAC Updating

In this mode, LDAC is held low while data is clocked into the

input shift register. The addressed DAC output is updated on

the rising edge of

Simultaneous Updating of All DACs

SYNC.

In this mode, LDAC is held high while data is clocked into the

input shift register. All DAC outputs are asynchronously updated

by taking LDAC low after SYNC has been taken high. The

update now occurs on the falling edge of

ASYNCHRONOUS CLEAR (

LDAC.

CLR)

CLR is an active low clear that allows the outputs to be cleared

to either zero-scale code or midscale code. The clear code value is

user-selectable via the CLR select bit of the control register (see

the Control Register section). It is necessary to maintain CLR low

for a minimum amount of time to complete the operation (see

Figure 2). When the CLR signal is returned high, the output

remains at the cleared value until a new value is programmed.

The outputs cannot be updated with a new value while the

CONFIGURING THE AD5722/AD5732/AD5752

CLR

pin is low. A clear operation can also be performed via the clear

command in the control register.

When the power supplies are applied to the AD5722/AD5732/

AD5752, the power-on reset circuit ensures that all registers

default to 0. This places all channels in power-down mode. The

first communication to the AD5722/AD5732/AD5752 should be

to set the required output range on all channels (the default range

is the 5 V unipolar range) by writing to the output range select

power on the required channels. To program an output value on

a channel, that channel must first be powered up; any writes to a

channel while it is in power-down mode are ignored. The AD5722/

AD5732/AD5752 operate with a wide power supply range. It is

important that the power supply applied to the parts provide

adequate headroom to support the chosen output ranges.

TRANSFER FUNCTION

Table 7 to Table 15 show the relationships of the ideal input

code to output voltage for the AD5752, AD5732, and AD5722,

respectively, for all output voltage ranges. For unipolar output

ranges, the data coding is straight binary. For bipolar output

ranges, the data coding is user selectable via the BIN/2sCOMP









REFIN

OUT

Gain

pin and can be either offset binary or twos complement.

For a unipolar output range, the output voltage expression is

given by

For a bipolar output range, the output voltage expression is given by

REFIN

OUT

Gain

−









where:

D is the decimal equivalent of the code loaded to the DAC.

N is the bit resolution of the DAC.

VREFIN is the reference voltage applied at the REFIN pin.

Gain is an internal gain whose value depends on the output

range selected by the user, as shown in Table 6.

Table 6. Internal Gain Values

Output Range (V)

Gain Value

+10

+10.8

4.32

±5

±10

±10.8

8.64

AD5752 датащи(PDF) 20 Page - Analog Devices

AD5752 датащи(HTML) 20 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

датащи скачать

ссылки URL