AD5722/AD5732/AD5752

Rev. 0 | Page 9 of 32

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

24

23

22

21

20

19

18

17

16

15

14

13

1

2

3

4

5

6

7

8

9

10

11

12

AD5722/

AD5732/

AD5752

CLR

LDAC

NC

NC

SYNC

NC

BIN/2sCOMP

GND

SDO

REFIN

SIG_GND

SCLK

SDIN

NC

NC

SIG_GND

DAC_GND

DAC_GND

NC

TOP VIEW

(Not to Scale)

NOTES

1. NC = NO CONNECT

2. IT IS RECOMMENDED THAT THE

EXPOSED PAD BE THERMALLY

CONNECTED TO A COPPER PLANE

FOR ENHANCED THERMAL

PERFORMANCE.

Figure 5. Pin Configuration

Table 5. Pin Function Descriptions

Pin No.

Mnemonic

Description

1

Negative Analog Supply. Voltage ranges from −4.5 V to −16.5 V. This pin can be connected to 0 V if output

ranges are unipolar.

2, 4, 6, 12,

13, 22

NC

Do not connect to these pins.

3

Analog Output Voltage of DAC A. The output amplifier is capable of directly driving a 2 kΩ, 4000 pF load.

5

BIN/2sCOMP

complement. (For unipolar output ranges, coding is always straight binary.)

7

SYNC

Active Low Input. This is the frame synchronization signal for the serial interface. While SYNC is low, data is

transferred on the falling edge of SCLK. Data is latched on the rising edge of SYNC.

8

SCLK

Serial Clock Input. Data is clocked into the shift register on the falling edge of SCLK. This operates at clock

speeds up to 30 MHz.

9

SDIN

Serial Data Input. Data must be valid on the falling edge of SCLK.

10

LDAC

Load DAC, Logic Input. This is used to update the DAC registers and, consequently, the analog outputs. When

this pin is tied permanently low, the addressed DAC register is updated on the rising edge of SYNC. If LDAC is

held high during the write cycle, the DAC input register is updated, but the output update is held off until the

falling edge of LDAC. In this mode, all analog outputs can be updated simultaneously on the falling edge of

LDAC. The LDAC pin should not be left unconnected.

11

CLR

Active Low Input. Asserting this pin sets the DAC registers to zero-scale code or midscale code (user-selectable).

14

Digital Supply. Voltage ranges from 2.7 V to 5.5 V.

15

GND

Ground Reference.

16

SDO

Serial Data Output. Used to clock data from the serial register in daisy-chain or readback mode. Data is clocked

out on the rising edge of SCLK and is valid on the falling edge of SCLK.

17

REFIN

External Reference Voltage Input. Reference input range is 2 V to 3 V. REFIN = 2.5 V for specified performance.

18, 19

DAC_GND

Ground Reference for the Two Digital-to-Analog Converters (DACs).

20, 21

SIG_GND

Ground Reference for the Two Output Amplifiers.

23

Analog Output Voltage of DAC B. The output amplifier is capable of directly driving a 2 kΩ, 4000 pF load.

24

Positive Analog Supply. Voltage ranges from 4.5 V to 16.5 V.

25 (EPAD)

Exposed

Paddle

(EPAD)

Negative Analog Supply Connection. Voltage ranges from −4.5 V to −16.5 V. This paddle can be connected to

0 V if output ranges are unipolar. The paddle can be left electrically unconnected provided that a supply

plane for enhanced thermal performance.