AD5752 datasheet(18/32 Pages) AD

18 / 32 page

AD5722/AD5732/AD5752

Rev. 0 | Page 18 of 32

THEORY OF OPERATION

The AD5722/AD5732/AD5752 are dual, 12-/14-/16-bit, serial

input, unipolar/bipolar, voltage output DACs. They operate

from unipolar supply voltages of +4.5 V to +16.5 V or bipolar

supply voltages of ±4.5 V to ±16.5 V. In addition, the parts have

software-selectable output ranges of +5 V, +10 V, +10.8 V, ±5 V,

±10 V, and ±10.8 V. Data is written to the AD5722/AD5732/

AD5752 in a 24-bit word format via a 3-wire serial interface.

The devices also offer an SDO pin to facilitate daisy-chaining

or readback.

The AD5722/AD5732/AD5752 incorporate a power-on reset

circuit to ensure that the DAC registers power up loaded with

0x0000. When powered on, the outputs are clamped to 0 V via

a low impedance path.

ARCHITECTURE

The DAC architecture consists of a string DAC followed by an

output amplifier. Figure 38 shows a block diagram of the DAC

architecture. The reference input is buffered before being

applied to the DAC.

GND

RESISTOR

STRING

REF (+)

REF (–)

CONFIGURABLE

OUTPUT

AMPLIFIER

OUTPUT

RANGE CONTROL

REFIN

DAC REGISTER

VOUTX

Figure 38. DAC Architecture Block Diagram

The resistor string structure is shown in Figure 39. It is a string

of resistors, each of value R. The code loaded to the DAC register

determines the node on the string where the voltage is to be

tapped off and fed into the output amplifier. The voltage is

tapped off by closing one of the switches connecting the string

to the amplifier. Because it is a string of resistors, it is guaranteed

monotonic.

TO OUTPUT

AMPLIFIER

REFIN

Figure 39. Resistor String Structure

Output Amplifiers

The output amplifiers are capable of generating both unipolar

and bipolar output voltages. They are capable of driving a load

of 2 kΩ in parallel with 4000 pF to GND. The source and sink

capabilities of the output amplifiers can be seen in Figure 26.

The slew rate is 3.5 V/µs with a full-scale settling time of 10 µs.

Reference Buffers

The AD5722/AD5732/AD5752 require an external reference

source. The reference input has an input range of 2 V to 3 V,

with 2.5 V for specified performance. This input voltage is then

buffered before it is applied to the DAC cores.

SERIAL INTERFACE

The AD5722/AD5732/AD5752 are controlled over a versatile

3-wire serial interface that operates at clock rates up to 30 MHz.

It is compatible with SPI, QSPI™, MICROWIRE™, and DSP

standards.

Input Shift Register

The input shift register is 24 bits wide. Data is loaded into the

device MSB first as a 24-bit word under the control of a serial

clock input, SCLK. The input register consists of a read/write

bit, three register select bits, three DAC address bits, and 16 data

bits. The timing diagram for this operation is shown in Figure 2.

AD5752 датащи(PDF) 18 Page - Analog Devices

AD5752 датащи(HTML) 18 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

датащи скачать

ссылки URL