AD9958SLASHPCBZ datasheet(22/44 Pages) AD

22 / 44 page

AD9958

Rev. A | Page 22 of 44

In modulation mode, the amplitude frequency phase (AFP)

select bits (CFR[23:22]) and modulation level bits (FR1[9:8])

are programmed to configure the modulation type and level

(see Table 6 and Table 7). Note that the linear sweep enable bit

must be set to Logic 0 in direct modulation mode.

Table 6. Modulation Type Configuration

AFP Select

(CFR[23:22])

Linear Sweep Enable

(CFR[14])

Description

Modulation disabled

Amplitude modulation

Frequency modulation

Phase modulation

Table 7. Modulation Level Selection

Modulation Level (FR1[9:8])

Description

Two-level modulation

Four-level modulation

Eight-level modulation

16-level modulation

When modulating, the RU/RD function can be limited based

on pins available for controlling the feature. The SDIO_x pins

are for RU/RD only, not for modulation.

Table 8. RU/RD Profile Pin Assignments

Ramp-Up/Ramp-Down

(RU/RD) (FR1[11:10])

Description

RU/RD disabled

Only Profile Pin P2 and Profile Pin P3

available for RU/RD operation

Only Profile Pin P3 available for RU/RD

operation

Only SDIO_1, SDIO_2, and SDIO_3

pins available for RU/RD operation;

this forces the serial I/O to be used

only in 1-bit mode

If the profile pins are used for RU/RD, Logic 0 is for ramp-up

and Logic 1 is for ramp-down.

Because of the two channels and limited data pins, it is

necessary to assign the profile pins and/or SDIO_1, SDIO_2,

and SDIO_3 pins to a dedicated channel. This is controlled by

the profile pin configuration (PPC) bits (FR1[14:12]). Each of the

following modulation descriptions incorporates data pin

assignments.

Two-Level Modulation—No RU/RD

The modulation level bits (FR1[9:8]) are set to 00 (two-level).

The AFP select bits (CFR[23:22]) are set to the desired modulation

type. The RU/RD bits (FR1[11:10]) and the linear sweep enable

bit (CFR[14]) are disabled. Table 9 displays how the profile pins

and channels are assigned.

As shown in Table 9, only Profile Pin P2 can be used to modulate

Channel 0. If frequency modulation is selected and Profile Pin P2

is Logic 0, Channel Frequency Tuning Word 0 (Register 0x04) is

chosen; if Profile Pin P2 is Logic 1, Channel Word 1 (Register

0x0A) is chosen.

Four-Level Modulation—No RU/RD

The modulation level bits are set to 01 (four-level). The AFP

select bits (CFR[23:22]) are set to the desired modulation type.

The RU/RD bits (FR1[11:10]) and the linear sweep enable bit

(CFR[14]) are disabled. Table 10 displays how the profile pins

and channels are assigned to each other.

For the conditions in Table 10, the profile (channel word)

Pins [P0:P1] or Profile Pins [P2:P3].

For example, if PPC = 101, [P0:P1] = 11, and [P2:P3] = 01, then

the contents of the Channel Word 3 register of Channel 0 are

presented to the output of Channel 0 and the contents of the

Channel Word 1 register of Channel 1 are presented to the

output of Channel 1.

Table 9. Profile Pin Channel Assignments

Profile Pin Configuration (PPC) (FR1[14:12])

Description

XXX

N/A

CH0

CH1

Two-level modulation, both channels, no RU/RD

Table 10. Profile Pin and Channel Assignments

Profile Pin Configuration (PPC) (FR1[14:12])

Description

101

CH0

CH1

Four-level modulation on CH0 and CH1, no RU/RD

AD9958/PCBZ датащи(PDF) 22 Page - Analog Devices

AD9958/PCBZ датащи(HTML) 22 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

датащи скачать

ссылки URL