| поискавой системы для электроныых деталей |
|
L9924L датащи(PDF) 75 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
L9924L датащи(HTML) 75 Page - STMicroelectronics |
|
75 / 84 page ![]() DocID028840 Rev 3 75/84 L9924L SPI interface 83 12.4.16 CP-SPREAD-SPECTRUM & LIN SETTING register [0x08] This register is used to activate/deactivate the spread spectrum strategy for the charge pump module and to choose the relevant modulation frequency; it also contains some LIN setting. Table 58. CP-SPREAD-SPECTRUM & LIN SETTING register [0x08] Bit Bit Name Reset Value Description 13 Reserved - - 12 WOBBLE_MODE_DIS 0 CP wobble mode disable: 0: Pseudo-random wobble is active, (Default) 1: Wobble mode is off 11 WOBBLE_FREQUENCY 0 CP wobble frequency selector: 0: 8 kHz (Default) 1: 16 kHz 10-5 Reserved - - 4 LIN_PU_DIS 0 LIN pull-up resistor disable bit: 0: LIN pull-up resistor is enabled (Default) 1: LIN pull-up resistor is disabled 3LIN_IN_USE (1) 0 LIN transceiver enable bit: 0: LIN transceiver is disabled (Default) 1: LIN transceiver is enabled. This mode is effective only when respective OTP protection bit isn’t programmed. OTP protection status can be acquired by reading LIN_PROT_OTP bit in [0x1F] register 2 SPI_LINRX_ONLY 0 LIN receiver-only enable bit: 0: Both LIN receiver and transmitter are available (Default) 1: LIN transmitter is unavailable 1 SPI_LINTX_TOUT (1) 1. In order to establish LIN traffic and related error handling it is mandatory LIN_IN_USE=1: write 0x0008 ' [0x08] register, SPI TX frame 0xA00008. Conversely SPI_LINTX_TOUT bit can be optionally set to enable here below 12-ms LIN error handling features: "LIN bus 12-ms permanent dominant, notified into LIN_PERM_DOM R/O bit in [0x12] register "LIN TX dominant 12-ms time-out, notified into LIN_TX_DOM R/O bit in [0x12] register In this case: write 0x000A ' [0x08] register, SPI TX frame 0xA0400A. 0 LIN TX dominant 12ms time-out enable bit: 0: LIN TX dominant time-out detection is disabled (Default) 1: LIN TX dominant time-out detection is enabled 0 LINFLASH 0 LIN flash mode enable bit: 0: Flash mode is disabled (Default) 1: Flash mode is enabled. This mode allows to increase standard high-speed data rate (>19.2kb/s) |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |