AMC7836IPAPR datasheet(41/91 Pages) TI2

41 / 91 page

AMC7836

www.ti.com

SLAS986D – NOVEMBER 2014 – REVISED FEBRUARY 2018

Product Folder Links: AMC7836

Submit Documentation Feedback

7.4.2 All-Negative DAC Range Mode

In the AMC7836 all-negative DAC range mode, each of the four DAC groups is set to a negative voltage output

range (–5 to 0 V or –10 to 0 V).

Although the maximum DAC output does not exceed 0 V, the common AVCC voltage (AVCC = AVCC_AB =

AVCC_CD) must still satisfy a minimum voltage of 4.7 V to comply with the device operating conditions. In this

case a recommended approach is to tie the AVCC, AVDD, and DVDD supply pins to a common potential.

The minimum DAC output for each group cannot be lower than the voltage on the corresponding AVSS pins

(AVEE, AVSSB, AVSSC, and AVSSD). The AVSS pins are not required to be tied to the same potential and typically

the negative voltage at each AVSS pin is dictated by the desired operating DAC negative output range. One

exception is the AVEE pin which must be the lowest potential in the device. The thermal pad should be either tied

to the same potential as the AVEE pin or left disconnected. Table 6 lists the typical configurations for this mode.

Table 6. All-Negative DAC Range Mode Typical Configuration

NOTES

TYPICAL CONNECTION

AVDD

5 V

DVDD

DVDD must be equal to AVDD.

5 V

IOVDD

IOVDD must be equal to or less than DVDD.

1.8 V to 5 V

AVCC_AB, AVCC_CD

The AVCC_AB and AVCC_CD pins must be tied

to the same potential (AVCC).

5 V

AVEE

AVEE must be the lowest potential in the

device.

AVEE must be less than or equal to the

minimum possible output voltage for DAC

group A.

AVEE ≤ –5 V

AVEE ≤ –10 V

AVSSB, AVSSC, AVSSD

AVSSn must be less than or equal to the

minimum possible output voltage for DAC

group n (n = B, C, D).

AVEE ≤ AVSSn ≤ –5 V

AVEE ≤ AVSSn ≤ –10 V

Thermal Pad

AVEE or,

Floating

After power-on or a reset event the output range for each DAC group is set automatically by the voltage present

in the corresponding AVSS pin. In the all-negative DAC range mode all AVSS pins should be connected to a

voltage lower than AVSSTH. If this condition is satisfied, all four DAC groups will initialize by default to the –10- to

0-V range. Because the negative clamp voltage is only dependent on the voltage in the AVSS pin, the default

–10- to 0-V output range presents no risk even when the AVSS voltage is greater than –10 V. In this case the

DAC group output should be modified to the –5 to 0 V range after initialization by setting the corresponding DAC

range register (address 0x1E to 0x1F) to 101b.

AMC7836IPAPR датащи(PDF) 41 Page - Texas Instruments

AMC7836IPAPR датащи(HTML) 41 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91

датащи скачать

ссылки URL