DSP56303 datasheet(127/292 Pages) FREESCALE

127 / 292 page

Host Programmer Model

DSP56303 User’s Manual, Rev. 2

Freescale Semiconductor

6-27

Note:

The external host should never read the RXH:RXM:RXL registers if the ISR[RXDF]

bit is cleared.

6.7.6 Transmit Data Registers (TXH:TXM:TXL)

The host processor views the transmit byte registers as three 8-bit write-only registers. These

registers are the transmit high register (TXH), the transmit middle register (TXM), and the

transmit low register (TXL). These registers send data to the high, middle, and low bytes,

respectively, of the HRX register and are selected by the external host address inputs, HA[2–0],

during a host processor write operation.

If ICR[HLEND] is set, the TXH register is located at address $7, the TXM register at $6, and the

TXL register at $5. If the HLEND bit in the ICR is cleared, the TXH register is located at address

$5, the TXM register at $6, and the TXL register at $7.

Data can be written into the transmit byte registers when the ISR transmit data register empty

(TXDE) bit is set. The host processor can program the ICR[TREQ] bit to assert the external

HREQ/HTRQ signal when ISR[TXDE] is set. This informs the host processor that the transmit

byte registers are empty. Writing to the data register at host address $7 clears the ISR[TXDE] bit.

The contents of the transmit byte registers are transferred as 24-bit data to the HRX register when

both ISR[TXDE] and HSR[HRDF] are cleared. This transfer operation sets HSR[TXDE] and

HSR[HRDF]. The external host should never write to the TXH:TXM:TXL registers if the

ISR[TXDE] bit is cleared.

Note:

When data is written to a peripheral device, there is a two-cycle pipeline delay until

any status bits affected by this operation are updated. If you read any of those status

bits within the next two cycles, the bit will not reflect its current status. For details, see

Section 5.4.1, Polling, on page 1-3.

6.7.7 Host-Side Registers After Reset

Table 6-18 shows the result of the four kinds of reset on bits in each of the HI08 registers seen by

the host processor. To cause a hardware reset, assert the RESET signal. To cause a software reset,

execute the RESET instruction. To reset the HEN bit individually, clear the HPCR[HEN] bit. To

cause a stop reset, execute the STOP instruction.

Table 6-18. Host-Side Registers After Reset

Name

Data

Reset Type

Reset

Individual Reset

STOP

ICR

All bits

—

CVR

HV[0–6]

$32

—

DSP56303 датащи(PDF) 127 Page - Freescale Semiconductor, Inc

DSP56303 датащи(HTML) 127 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL