AD9984A datasheet(27/44 Pages) AD

27 / 44 page

AD9984A

Rev. 0 | Page 27 of 44

Hex

Address

Read/Write,

Read Only

Bits

Default

Value

Description

**** *0**

Power-Down Pin Polarity. Sets the polarity of the signal on the

PWRDN pin.

0 = PWRDN polarity is negative.

1 = PWRDN polarity is positive.

**** **0*

Power-Down Fast Switching Control.

0 = Normal power-down operation.

1 = The chip stays powered up, and the outputs are put in high

impedance mode.

**** ***0

SOGOUT High Impedance Control.

0 = SOGOUT operates as normal during power-down.

1 = SOGOUT is in high impedance during power-down.

0x1F

R/W

7:5

100* ****

Output Select 1

Output Mode.

100 = 4:4:4 RGB mode.

101 = 4:2:2 YCbCr mode.

110 = 4:4:4 DDR mode.

***1 ****

Primary Output Enable.

0 = Primary output is in high impedance state.

1 = Primary output is enabled.

**** 0***

Secondary Output Enable.

0 = Secondary output is in high impedance state.

1 = Secondary output is enabled.

2:1

**** *10*

Output Drive Strength. Applies to all outputs except VSOUT.

00 = Low output drive strength.

01 = Medium output drive strength.

1x = High output drive strength.

**** ***0

Output Clock Invert. Applies to all clocks output on DATACK.

0 = Noninverted Pixel Clock.

1 = Inverted Pixel Clock.

0x20

R/W

7:6

0*** ****

Output Select 2

Output Clock Select.

00 = Pixel clock.

01 = 90° phase-shifted pixel clock.

10 = 2× pixel clock.

11 = 0.5× pixel clock.

*0** ****

Output High Impedance.

0 = Normal outputs.

1 = All outputs except SOGOUT in high impedance mode.

**0* ****

SOGOUT High Impedance.

0 = Normal drive.

1 = SOGOUT pin is in high impedance mode.

***0 ****

Field Output Polarity. Sets the polarity of the field output signal.

0 = Active low is an even field, active high is an odd field.

1 = Active low is an odd field, active high is an even field.

**** 1***

PLL Sync Filter Enable.

0 = PLL uses raw HSYNCx/SOGINx.

1 = PLL uses filtered Hsync/SOG.

**** *0**

Sync Processing Input Select. Selects the sync source for the sync

processor.

0 = Sync processing uses raw HSYNCx/SOGINx.

1 = Sync processing uses regenerated Hsync from sync filter.

**** ***0

Must be set to 1 for proper operation.

0x21

R/W

7:0

0010 0000

Must be set to default for proper operation.

0x22

R/W

7:0

0011 0010

Must be set to default for proper operation.

0x23

R/W

7:0

0000 1010

Sync Filter Window

Width

Sets the window of time around the regenerated Hsync leading

edge (in 25 ns steps) that sync pulses are allowed to pass through.

0x24

_*** ****

Sync Detect

HSYNC0 Detection.

0 = HSYNC0 is not active.

1 = HSYNC0 is active.

AD9984A датащи(PDF) 27 Page - Analog Devices

AD9984A датащи(HTML) 27 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

датащи скачать

ссылки URL