AD9163BBCZ datasheet(27/126 Pages) AD

27 / 126 page

Data Sheet

AD9163

Rev. D | Page 27 of 126

TERMINOLOGY

Integral Nonlinearity (INL)

INL is the maximum deviation of the actual analog output from

the ideal output, determined by a straight line drawn from zero

scale to full scale.

Differential Nonlinearity (DNL)

DNL is the measure of the variation in analog value, normalized

to full scale, associated with a 1 LSB change in digital input code.

Offset Error

Offset error is the deviation of the output current from the ideal

of 0 mA. For OUTPUT+, 0 mA output is expected when all

inputs are set to 0. For OUTPUT−, 0 mA output is expected

when all inputs are set to 1.

Gain Error

Gain error is the difference between the actual and ideal output

span. The actual span is determined by the difference between

the output when the input is at its minimum code and the

output when the input is at its maximum code.

Temperature Drift

Temperature drift is specified as the maximum change from the

ambient (25°C) value to the value at either TMIN or TMAX. For offset

and gain drift, the drift is reported in ppm of full-scale range

(FSR) per degree Celsius. For reference drift, the drift is reported

in ppm per degree Celsius.

Settling Time

Settling time is the time required for the output to reach and

remain within a specified error band around its final value,

measured from the start of the output transition.

Spurious-Free Dynamic Range (SFDR)

SFDR is the difference, in decibels, between the peak amplitude

of the output signal and the peak spurious signal within the dc

to Nyquist frequency of the DAC. Typically, energy in this band

is rejected by the interpolation filters. This specification,

therefore, defines how well the interpolation filters work and

the effect of other parasitic coupling paths on the DAC output.

Signal-to-Noise Ratio (SNR)

SNR is the ratio of the rms value of the measured output signal

to the rms sum of all other spectral components below the Nyquist

frequency, excluding the first six harmonics and dc. The value

for SNR is expressed in decibels.

Interpolation Filter

If the digital inputs to the DAC are sampled at a multiple rate of

the interpolation rate (fDATA), a digital filter can be constructed that

has a sharp transition band near fDATA/2. Images that typically

appear around the output data rate (fDAC) can be greatly

suppressed.

Adjacent Channel Leakage Ratio (ACLR)

ACLR is the ratio in decibels relative to the carrier (dBc)

between the measured power within a channel relative to its

adjacent channel.

Adjusted DAC Update Rate

The adjusted DAC update rate is the DAC update rate divided

by the smallest interpolating factor. For clarity on DACs with

multiple interpolating factors, the adjusted DAC update rate for

each interpolating factor may be given.

Physical Lane

Physical Lane x refers to SERDINx±.

Logical Lane

Logical Lane x refers to physical lanes after optionally being

remapped by the crossbar block (Register 0x308 to Register 0x30B).

Link Lane

Link Lane x refers to logical lanes considered in the link.

AD9163BBCZ датащи(PDF) 27 Page - Analog Devices

AD9163BBCZ датащи(HTML) 27 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL