PR31100ABC datasheet(5/26 Pages) PHILIPS

5 / 26 page

Philips Semiconductors

Preliminary specification

MIPS

PR31100

Highly integrated embedded processor

1996 Aug 07

IR Module

• IR consumer mode

– allows control of consumer electronic devices such as stereos,

TVs, VCRs, etc.

– programmable pulse parameters

– external analog LED circuitry

• IRDA communication mode

– allows communication with other IRDA devices such as FAX

machines, copiers, printers, etc.

– supported by UART module within PR31100

– external analog receiver preamp and LED circuitry

– data rate = up to 115 Kbps at 1 meter

• IR FSK communication mode

– supported by UART module within PR31100

– external analog IR chip(s) perform frequency modulation to

generate the desired IR communication mode protocol

– data rate = up to 36000 bps at 3 meters

• carrier detect state machine

– periodically enables IR receiver to check if a valid carrier is

present

Magicbus Module

• synchronous, serial 2–wire (clock and data), half–duplex

communications protocol

• supports low–cost, low–power peripherals

• supports maximum data rate of 14.75 Mbps

• DMA support for Magicbus receive and transmit

Power Module

• power–down modes for individual internal peripheral modules

• serial (SPI port) power supply control interface supported

• power management state machine has 4 states: RUNNING,

DOZING, SLEEP, and COMA

Serial Interconnect Bus (SIB) Module

• PR31100 contains holding and shift registers to support the serial

interface to the UCB1100 and/or other optional codec devices

• interface compatible with slave mode 3 of Crystal CS4216 codec

• synchronous, frame–based protocol

• PR31100 always master source of clock and frame frequency and

phase; programmable clock frequency

• each SIB frame consists of 128 clock cycles, further divided into 2

subframes or words of 64 bits each (supports up to 2 devices

simultaneously)

• independent DMA support for audio receive and transmit, telecom

receive and transmit

• supports 8–bit or 16–bit mono telecom formats

• supports 8–bit or 16–bit mono or stereo audio formats

• independently programmable audio and telecom sample rates

• CPU read/write registers for subframe control and status

System Peripheral Interface (SPI) Module

• provides interface to SPI peripherals and devices

• full–duplex, synchronous serial data transfers (data in, data out,

and clock signals)

• PR31100 supplies dedicated chip select and interrupt for an SPI

interface serial power supply

• 8–bit or 16–bit data word lengths for the SPI interface

• programmable SPI baud rate

Timer Module

• Real Time Clock (RTC) and Timer

• 40–bit counter (30.517 µsec granularity);

maximum uninterrupted time = 388.36 days

• 40–bit alarm register (30.517 µsec granularity)

• 16–bit periodic timer (0.868 µsec granularity);

maximum timeout = 56.8 msec

• interrupts on alarm, timer, and prior to RTC roll–over

UART Module

• 2 independent full–duplex UARTs

• programmable baud rate generator

• UART–A port used for serial control interface to external IR

module

• UART–B port used for general purpose serial control interface

• UART–A and UART–B DMA support for receive and transmit

Video Module

• bit–mapped graphics

• supports monochrome, grey scale, or color modes

• time–based dithering algorithm for grey scale and color modes

• supports multiple screen sizes

• supports split and non–split displays

• variable size and relocatable video buffer

• DMA support for fetching image data from video buffer

PR31100ABC датащи(PDF) 5 Page - NXP Semiconductors

PR31100ABC датащи(HTML) 5 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

датащи скачать

ссылки URL