PR31100ABC datasheet(4/26 Pages) PHILIPS

4 / 26 page

Philips Semiconductors

Preliminary specification

MIPS

PR31100

Highly integrated embedded processor

1996 Aug 07

OVERVIEW

Each of the on-chip peripherals consist of:

BIU Module

• System memory and PR31100 Bus Interface Unit (BIU)

– supports up to 2 banks of physical memory

– supports self–refreshing DRAM and SDRAM

– programmable parameters for each bank of DRAM or SDRAM

(row/column address configuration, refresh, burst modes, etc.)

• programmable chip select memory access

– 4 programmable (size, wait states, burst mode control) memory

device and general purpose chip selects

available for system ROM, SRAM, Flash

available for external port expansion registers

– 4 programmable (wait states, burst mode control) MagicCard or

general purpose chip selects

available for (future) MagicCard expansion memory

PR31100 provides the chip select and card detect signals

supports card insertion/removal timeouts

MagicCard requires minimal number of unique control/status

signals per port

• supports up to 2 identical full PCMCIA ports

– PR31100 and UCB1100 provide the control signals and accepts

the status signals which conform to the PCMCIA version 2.01

standard

– appropriate connector keying and level–shifting buffers required

for 3.3V versus 5V PCMCIA interface implementations

SIU Module

• multi–channel 32–bit DMA controller and System Interface Unit

(SIU)

• independent DMA channels for video, Magicbus, SIB to/from

UCB1100 audio/telecom codecs, high–speed serial port, IR UART,

and general purpose UART

• address decoding for submodules within System Interface Module

(SIM)

CPU Module

• R3000 RISC central processing unit core

– full 32–bit operation (registers, instructions, addresses)

– 32 general purpose 32–bit registers; 32–bit program counter

– MIPS RISC Instruction Set Architecture (ISA) supported

• on–chip cache

– 4 KByte direct–mapped instruction cache (I–cache)

physical address tag and valid bit per cache line

programmable burst size

instruction streaming mode supported

– 1 KByte data cache (D–cache)

physical address tag and valid bit per cache line

programmable burst size

write–through

– cache address snoop mode supported for DMA

– 4–level deep write buffer

• programmable memory protection

– separate read and write protection control for kernel and user

space

– 8 total protectable regions available, each individually

programmable, using breakpoint address, mask, control, and

status registers

– causes address exception on illegal reads or writes

• high–speed multiplier/accumulator

– on–chip hardware multiplier

– supports 16x16 or 32x32 multiplier operations, with 64–bit

accumulator

– existing multiply instructions are enhanced and new multiply

and add instructions are added to R3000 instruction set to

improve the performance of DSP applications

• CPU interface

– handles data bus, address bus, and control interface between

CPU core and rest of PR31100 logic

Clock Module

• PR31100 supports system–wide single crystal configuration,

besides the 32 KHz RTC XTAL (reduces cost, power, and board

space)

• common crystal rate divided to generate clock for CPU, video,

sound, telecom, UARTs, etc.

• external system crystal rate is vendor–dependent

• independent enabling or disabling of individual clocks under

software control, for power management

CHI Module

• high–speed serial Concentration Highway Interface (CHI) contains

logic for interfacing to external full–duplex serial

time–division–multiplexed (TDM) communication peripherals

• supports ISDN line interface chips and other PCM/TDM serial

devices

• CHI interface is programmable (number of channels, frame rate,

bit rate, etc.) to provide support for a variety of formats

• supports data rates up to 4.096 Mbps

• independent DMA support for CHI receive and transmit

Interrupt Module

• contains logic for individually enabling, reading, and clearing all

PR31100 interrupt sources

• interrupts generated from internal PR31100 modules or from edge

transitions on external signal pins

IO Module

• contains support for reading and writing the 7 bi–directional

general purpose IO pins and the 32 bi–directional multi–function

IO pins

• each IO port can generate a separate positive and negative edge

interrupt

• independently configurable IO ports allow PR31100 to support a

flexible and wide range of system applications and configurations

PR31100ABC датащи(PDF) 4 Page - NXP Semiconductors

PR31100ABC датащи(HTML) 4 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

датащи скачать

ссылки URL