USB97C201 datasheet(33/59 Pages) SMSC

33 / 59 page

SMSC USB97C201

Page 33

Rev. 11-05-03

DATASHEET

EP1RX_CTL

(0xB2 - RESET=0x00)

ENDPOINT 1 RECEIVE CONTROL REGISTER

BIT

NAME

R/W

DESCRIPTION

ENDPOINT CLEAR” command for this endpoint or USB

RESET clears this bit. Writing a “0” to this bit has no effect.

Reserved

This bit always reads “0”.

ENABLE

R/W

EP1 Receive is enabled in the SIE if this bit is set to a “1”,

otherwise, it is disabled.

Table 34 – Endpoint 1 Transmit Control Register

EP1TX_CTL

(0xB3 - RESET=0x00)

ENDPOINT 1 TRANSMIT CONTROL REGISTER

BIT

NAME

R/W

DESCRIPTION

Reserved

This bit always reads “0”.

Reserved

This bit always reads “0”.

Reserved

This bit always reads “0”.

R/W

When written with a “1”, allows the SIE to transfer data from

the buffer SRAM to EP1. Until the transmission or reception

is complete, OUT will be NAK’d. It is cleared by the SIE

when transmission of the packet has been completed.

Reserved

This bit always reads “0”.

STALL

R/W

When set to a “1”, EP1 TX will respond with the STALL

handshake to IN tokens. . Either the internal SIE or the user

may set this bit. Receipt of a “CLEAR FEATURE

ENDPOINT CLEAR” command for this endpoint or USB

RESET clears this bit. Writing a “0” to this bit has no effect.

Reserved

This bit always reads “0”.

ENABLE

EP1 Transmit is enabled in the SIE if this bit is set to a “1”,

otherwise, it is disabled.

Table 35 – Endpoint 2 Control Register

EP2_CTL

(0xB4 - RESET=0x00)

ENDPOINT 2 CONTROL REGISTER

BIT

NAME

R/W

DESCRIPTION

DIR

R/W

Setting this bit to a “1” indicates that the data flow is from the

ATA interface to the SIE, a “0” indicates the opposite

direction. When a “1”, the SIE will set the EP2_ERR bit in

the USB_STATUS register if an OUT token is received.

When a “0”, the EP2_ERR bit set if the SIE receives an IN

token.

RAMWR_

TOGVALID

R/W

If this bit is set to a “1” when writes to this register occur,

then the value of bit 5 written to this register will have effect.

If cleared, then the values of bit 5, when this register is

written, is ignored. This bit always returns “0” on reads.

RAMWR_

TOGGLE

R/W

Writing a “0” to this bit will enable writing of the 512 byte

SRAM A buffer and clear the RAMWRBC_A1/2 registers,

while writing a “1” will select loading of the SRAM B buffer

and clear the RAMWRBC_B1/2 registers. This bit indicates

which interleaved buffer is currently or was last written with

data. The RAMWRBC_A and RAMWRBC_B Registers

contain the byte counts for the last write to the A and B input

buffers, respectively. See Sections 6.4, 6.5, and 6.9 for

more information. To avoid interrupting a transfer that is in

progress, it is important not to write this bit until it is

completed. Note that if AutoToggle mode is enabled by bit 3

of the ATA_CTL register, this bit will reflect that current

buffer being written(1=B, 0=A).

USB97C201 датащи(PDF) 33 Page - SMSC Corporation

USB97C201 датащи(HTML) 33 Page - SMSC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59

датащи скачать

ссылки URL